Cisco XR 1200 series Command Reference Manual Download Page 370

Page: 370 / 432

show logging onboard

To display the onboard failure logging (OBFL) messages, use the

show logging onboard

command in

administration EXEC or mode.

show logging onboard

[

all

cbc

{

dump-all

dump-range

{

start-address

end-address

most-recent

{

fans

fan-tray-slot

| [

location node-id

]}

}] [

all|

continuous| historical| static-data

] [

detail| raw| summary

] [

location node-id

]

[verbose]

Syntax Description

Displays all file information.

all

Displays Can Bus Controller (CBC) OBFL commands.

cbc

Displays all OBFL records.

dump-all

Displays OBFL EEPROM data for a given range. Start and end address
ranges are from 0 to 4294967295.

dump-range

{

start-address

end-address

}

Displays the last five OBFL data records.

most-recent

Displays a specific fan tray slot.

fans fan-tray-slot

Displays OBFL messages from the designated node. The

node-id

argument is entered in the

rack/slot/module

notation.

location node-id

Displays diagnostic information.

diagnostic

Displays system environment information.

environment

Displays output from the message application.

error

Displays temperature information.

temperature

Displays the OBFL uptime.

uptime

Displays voltage information.

voltage

Displays continuous information.

continuous

Displays historical information.

historical

Display system descriptor data.

static-data

Displays detailed logging information.

detail

Displays raw OBFL data.

raw

Displays a summary of OBFL logging information.

summary

Cisco IOS XR System Monitoring Command Reference for the Cisco XR 12000 Series Router, Release 4.1

358

OL-24735-01

Onboard Failure Logging Commands

show logging onboard

Summary of Contents for XR 1200 series

















































































































































































































































































































































































































































Search results

Summary of Contents for XR 1200 series

Reviews:

Related manuals for XR 1200 series

Brands by name

Popular brands

Cisco XR 1200 series, Command Reference Manual

Search results

Summary of Contents for XR 1200 series

Reviews:

Related manuals for XR 1200 series

Brands by name

Popular brands