Cisco XR 1200 series Command Reference Manual Download Page 255

Page: 255 / 432

Description

Field

Sum of squares of the positive jitter values from the
destination to the source.

Sum2PositivesDS

Sum of squares of the positive jitter values from the
source to the destination.

Sum2PositivesSD

Sum of squares of the negative jitter values from the
destination to the source.

Sum2NegativesDS

Sum of squares of the negative jitter values from the
source to the destination.

Sum2NegativesSD

Target IP address.

Target Address

The output of the

show ipsla statistics aggregated detail

command varies depending on operation type. The

following sample output is from the

show ipsla statistics aggregated detail

command in tabular format,

when the output is split over multiple lines:

RP/0/0/CPU0:router#

show ipsla statistics aggregated detail 2

Captured Statistics

Multiple Lines per Entry

Line1:
Entry

= Entry number

StartT

= Start time of entry (hundredths of seconds)

Pth

= Path index

Hop

= Hop in path index

Dst

= Time distribution index

Comps

= Operations completed

SumCmp

= Sum of RTT (milliseconds)

Line2:
SumCmp2H = Sum of RTT squared high 32 bits (milliseconds)
SumCmp2L = Sum of RTT squared low 32 bits (milliseconds)
TMax

= RTT maximum (milliseconds)

TMin

= RTT minimum (milliseconds)

Entry StartT

Pth Hop Dst Comps

SumCmp

SumCmp2H

SumCmp2L

TMax

TMin

1134423910701 1

367

1231

1134423851116 1

129

2419

1134423070733 1

101

1119

This table describes the significant fields shown in the display.

Table 25: show ipsla statistics aggregated detail Field Descriptions

Description

Field

Entry number.

Entry

Start time of entry, in hundredths of seconds.

StartT

Cisco IOS XR System Monitoring Command Reference for the Cisco XR 12000 Series Router, Release 4.1

OL-24735-01

243

IP Service Level Agreement Commands

show ipsla statistics aggregated

Summary of Contents for XR 1200 series

















































































































































































































































































































































































































































Search results

Summary of Contents for XR 1200 series

Reviews:

Related manuals for XR 1200 series

Brands by name

Popular brands

Cisco XR 1200 series, Command Reference Manual

Search results

Summary of Contents for XR 1200 series

Reviews:

Related manuals for XR 1200 series

Brands by name

Popular brands