Cisco XR 1200 series Command Reference Manual Download Page 152

Page: 152 / 432

filter

To define the type of information that are kept in the history table for the IP SLA operation, use the

filter

command in IP SLA operation history configuration mode. To unset the history filter, use the

form of this

command.

filter

{

all| failures

}

no filter

Syntax Description

Stores history data for all operations, if set.

all

Stores data for operations that failed, if set.

failures

Command Default

The default is not to collect the history unless the

filter

command is enabled.

Command Modes

IP SLA operation history configuration

Command History

Modification

Release

This command was introduced.

Release 3.3.0

Usage Guidelines

The

filter

command is supported only to configure the following operations:

•

IP SLA ICMP path-echo

•

IP SLA ICMP echo

•

IP SLA UDP echo

If you use the

form of the

filter

command, the history statistics are not collected.

Task ID

Operations

Task ID

read, write

monitor

Examples

The following example shows how to use the

filter

command in IP SLA UDP echo configuration mode:

RP/0/0/CPU0:router#

configure

RP/0/0/CPU0:router(config)#

ipsla

Cisco IOS XR System Monitoring Command Reference for the Cisco XR 12000 Series Router, Release 4.1

140

OL-24735-01

IP Service Level Agreement Commands

filter

Summary of Contents for XR 1200 series

















































































































































































































































































































































































































































Search results

Summary of Contents for XR 1200 series

Reviews:

Related manuals for XR 1200 series

Brands by name

Popular brands

Cisco XR 1200 series, Command Reference Manual

Search results

Summary of Contents for XR 1200 series

Reviews:

Related manuals for XR 1200 series

Brands by name

Popular brands