Cisco XR 1200 series Command Reference Manual Download Page 133

Page: 133 / 432

buckets (history)

To set the number of history buckets that are kept during the lifetime of the IP SLA operation, use the

buckets

command in IP SLA operation history configuration mode. To use the default value, use the

form of this

command.

buckets buckets

no buckets

Syntax Description

Number of history buckets that are kept during the lifetime of an IP SLA operation.
Range is 1 to 60.

buckets

Command Default

The default value is 15 buckets.

Command Modes

IP SLA operation history configuration

Command History

Modification

Release

This command was introduced.

Release 3.3.0

Usage Guidelines

The

buckets

command is supported only to configure the following operations:

•

IP SLA ICMP path-echo

•

IP SLA ICMP echo

•

IP SLA UDP echo

Task ID

Operations

Task ID

read, write

monitor

Examples

The following example shows how to use the

buckets

command in IP SLA UDP echo configuration mode:

RP/0/0/CPU0:router#

configure

RP/0/0/CPU0:router(config)#

ipsla

RP/0/0/CPU0:router(config-ipsla)#

operation 1

RP/0/0/CPU0:router(config-ipsla-op)#

type udp echo

RP/0/0/CPU0:router(config-ipsla-udp-echo)#

history

RP/0/0/CPU0:router(config-ipsla-op-hist)#

buckets 30

Cisco IOS XR System Monitoring Command Reference for the Cisco XR 12000 Series Router, Release 4.1

OL-24735-01

121

IP Service Level Agreement Commands

buckets (history)

Summary of Contents for XR 1200 series

















































































































































































































































































































































































































































Search results

Summary of Contents for XR 1200 series

Reviews:

Related manuals for XR 1200 series

Brands by name

Popular brands

Cisco XR 1200 series, Command Reference Manual

Search results

Summary of Contents for XR 1200 series

Reviews:

Related manuals for XR 1200 series

Brands by name

Popular brands