Cisco XR 1200 series Command Reference Manual Download Page 426

Page: 426 / 432

clear counters

To clear the interface counters, use the

clear counters

command in EXEC mode.

clear counters

[

all

type interface-path-id

]

Syntax Description

(Optional) Clears counters on all interfaces.

all

(Optional) Interface type. For more information, use the question mark (

) online

help function.

type

(Optional) Physical interface or virtual interface.

Use the

show interfaces

command to see a list of all interfaces currently

configured on the router.

Note

For more information about the syntax for the router, use the question mark (

) online

help function.

interface-path-id

Command Default

Counters for all interfaces are cleared.

Command Modes

EXEC

Command History

Modification

Release

This command was introduced.

Release 3.2

Usage Guidelines

Use the

clear counters

command to clear all the statistics counters displayed by the

show interfaces

command.

If no optional arguments are supplied or if the

all

keyword is specified, then the counters for all interfaces are

cleared. If an interface type is specified, then only the counters for that interface are cleared.

The

clear counters

command with the

all

option clears counters on all interfaces. When you enter this

command, the system prompts you for confirmation. You must then press Enter or the

key for the

clear

counters

command to take effect.

This command does not clear counters retrieved using Simple Network Management Protocol (SNMP),
but only those counters displayed with the

show interfaces

command.

Note

Cisco IOS XR System Monitoring Command Reference for the Cisco XR 12000 Series Router, Release 4.1

414

OL-24735-01

Statistics Service Commands

clear counters

Summary of Contents for XR 1200 series

















































































































































































































































































































































































































































Search results

Summary of Contents for XR 1200 series

Reviews:

Related manuals for XR 1200 series

Brands by name

Popular brands

Cisco XR 1200 series, Command Reference Manual

Search results

Summary of Contents for XR 1200 series

Reviews:

Related manuals for XR 1200 series

Brands by name

Popular brands