Cisco XR 1200 series Command Reference Manual Download Page 355 | Manualshive

Page: 355 / 432

background image

severity

To specify the filter level for logs, use the

severity

command in logging archive configuration mode. To return

to the default, use the

no

form of this command.

severity

{

severity

}

no severity

Syntax Description

Severity level for determining which messages are logged to the archive. Possible severity
levels and their respective system conditions are listed under

Table 29: Severity Levels for

Messages, on page 312

in the

“

Usage Guidelines

”

section. The default is

informational

.

severity

Command Default

Informational

Command Modes

Logging archive configuration

Command History

Modification

Release

This command was introduced.

Release 3.2

Usage Guidelines

Use the

severity

command to specify the filter level for syslog messages. All syslog messages higher in

severity or the same as the configured value are logged to the archive.

Table 29: Severity Levels for Messages, on page 312

describes the acceptable severity levels for the

severity

argument.

Task ID

Operations

Task ID

read, write

logging

Examples

This example shows how to specify that warning conditions and higher-severity messages are logged to the
archive:

RP/0/0/CPU0:router(config)#

logging archive

RP/0/0/CPU0:router(config-logging-arch)#

severity warnings

Cisco IOS XR System Monitoring Command Reference for the Cisco XR 12000 Series Router, Release 4.1

OL-24735-01

343

Logging Services Commands

severity

«
...
353
354
355
356
357
...
»

Summary of Contents for XR 1200 series

















































































































































































































































































































































































































































Reviews:

No comments

Related manuals for XR 1200 series

Brand: Sagem Pages: 19

Brand: Panasonic Pages: 18

RouterBOARD SXT 5HnD

Brand: MikroTik Pages: 2

ION 1200 Series

Brand: PaloAlto Networks Pages: 90

Brand: NETGEAR Pages: 2

DesignCore RVP-TDA3 Series

Brand: D3 Pages: 34

Brand: Keithley Pages: 98

Brand: Lanner Pages: 59

Brand: Digisol Pages: 22

DEEP LEARNING PLUS

Brand: Concept Pro Pages: 28

Brand: Quatech Pages: 98

Brand: BinTec Pages: 2

Brand: Airlinkplus Pages: 24

Brand: NAUTICAST Pages: 20

Brand: H3C Pages: 148

Temporary Target Board M38517T-ADS

Brand: Renesas Pages: 14

Brand: Encore Networks Pages: 2

Brand: VegaStream Pages: 41

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands