Cisco XR 1200 series Command Reference Manual Download Page 206

Page: 206 / 432

RP/0/0/CPU0:router(config-ipsla-react)#

react packet-loss dest-to-source

RP/0/0/CPU0:router(config-ipsla-react-cond)#

The following example shows how to use the

react

command with the

rtt

keyword:

RP/0/0/CPU0:router#

configure

RP/0/0/CPU0:router(config)#

ipsla

RP/0/0/CPU0:router(config-ipsla)#

reaction operation 432

RP/0/0/CPU0:router(config-ipsla-react)#

react rtt

RP/0/0/CPU0:router(config-ipsla-react-cond)#

The following example shows how to use the

react

command with the

timeout

keyword:

RP/0/0/CPU0:router#

configure

RP/0/0/CPU0:router(config)#

ipsla

RP/0/0/CPU0:router(config-ipsla)#

reaction operation 432

RP/0/0/CPU0:router(config-ipsla-react)#

react timeout

RP/0/0/CPU0:router(config-ipsla-react-cond)#

The following example shows how to use the

react

command with the

verify-error

keyword:

RP/0/0/CPU0:router#

configure

RP/0/0/CPU0:router(config)#

ipsla

RP/0/0/CPU0:router(config-ipsla)#

reaction operation 432

RP/0/0/CPU0:router(config-ipsla-react)#

react verify-error

RP/0/0/CPU0:router(config-ipsla-react-cond)#

Related Commands

Description

Command

Specifies what action or combination of actions the
operation performs when you configure the

react

command or when threshold events occur.

action (IP SLA), on page 117

Configures an IP SLA operation.

operation, on page 174

Schedules an IP SLA operation.

schedule operation, on page 215

Sets the lower-limit and upper-limit values.

threshold, on page 267

Takes action on average values to violate a threshold.

threshold type average, on page 269

Takes action after a number of consecutive violations.

threshold type consecutive, on page 271

Takes action immediately upon a threshold violation.

threshold type immediate, on page 273

Takes action upon X violations in Y probe operations.

threshold type xofy, on page 275

Cisco IOS XR System Monitoring Command Reference for the Cisco XR 12000 Series Router, Release 4.1

194

OL-24735-01

IP Service Level Agreement Commands

react

Summary of Contents for XR 1200 series

















































































































































































































































































































































































































































Search results

Summary of Contents for XR 1200 series

Reviews:

Related manuals for XR 1200 series

Brands by name

Popular brands

Cisco XR 1200 series, Command Reference Manual

Search results

Summary of Contents for XR 1200 series

Reviews:

Related manuals for XR 1200 series

Brands by name

Popular brands