Cisco XR 1200 series Command Reference Manual Download Page 245 | Manualshive

Page: 245 / 432

background image

show ipsla responder statistics ports

To display the number of probes that are received or handled by the currently active ports on the responder,
use the

show ipsla responder statistics ports

command in EXEC mode.

show ipsla responder statistics ports

Syntax Description

This command has no keywords or arguments.

Command Default

None

Command Modes

EXEC

Command History

Modification

Release

This command was introduced.

Release 3.3.0

Usage Guidelines

The output of the

show ipsla responder statistics port

command is available only for specific intervals of

time in which only nonpermanent ports are being used at the responder. The reason is that the responder closes
the nonpermanent ports after each operation cycle. However, if both permanent and nonpermanent ports are
used, the output always contains rows for the permanent ports. The rows for the nonpermanent ports are
displayed only if those nonpermanent ports are enabled at the instant the command is issued.

Task ID

Operations

Task ID

read

monitor

Examples

The following sample output is from the

show ipsla responder statistics port

command:

RP/0/0/CPU0:router#

show ipsla responder statistics port

Port 12709

Local Address ...

NumberOfProbes

2

Port 12213

Local Address ...

NumberOfProbes

1

Port 55690

Local Address ...

NumberOfProbes

376

This table describes the significant fields shown in the display.

Cisco IOS XR System Monitoring Command Reference for the Cisco XR 12000 Series Router, Release 4.1

OL-24735-01

233

IP Service Level Agreement Commands

show ipsla responder statistics ports

«
...
243
244
245
246
247
...
»

Summary of Contents for XR 1200 series

















































































































































































































































































































































































































































Reviews:

No comments

Related manuals for XR 1200 series

ShareCenter Quattro DNS-345

Brand: D-Link Pages: 40

ShareCenter Quattro DNS-345

Brand: D-Link Pages: 4

ShareCenter DNS-343

Brand: D-Link Pages: 12

AirPlus G DWL-G710

Brand: D-Link Pages: 5

MYDLINK DNR-322L

Brand: D-Link Pages: 4

mydlink DNR-312L

Brand: D-Link Pages: 8

Brand: D-Link Pages: 12

Brand: D-Link Pages: 16

Brand: D-Link Pages: 88

Brand: Zonet Pages: 8

Brand: Dahua Pages: 24

Brand: Eneo Pages: 68

Brand: Infoblox Pages: 13

Brand: Ubiquiti Pages: 23

Brand: ZyXEL Communications Pages: 2

S3000-EI Series

Brand: Quidway Pages: 16

Brand: ZyXEL Communications Pages: 12

NVR2104/2108HS-W-4KS2 1U

Brand: Dahua Technology Pages: 363

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands