Cisco XR 1200 series Command Reference Manual Download Page 30 | Manualshive

Page: 30 / 432

background image

logging correlator apply ruleset

To apply and activate a correlation rule set and enter correlation apply rule set configuration mode, use the

logging correlator apply ruleset

command in global configuration mode. To deactivate a correlation rule

set, use the

no

form of this command.

logging correlator apply ruleset correlation-ruleset

[

all-of-router

|

context name

|

location node-id

]

no logging correlator apply ruleset correlation-ruleset

[

all-of-router

|

context name

|

location node-id

]

Syntax Description

Name of the correlation rule set to be applied.

correlation-ruleset

(Optional) Applies the correlation rule set to the entire router.

all-of-router

(Optional) Applies the correlation rule set to the specified context. Unlimited
number of contexts. The

name

string is limited to 32 characters.

context name

(Optional) Applies the correlation rule to the specified node. The

node-id

argument is entered in the

rack/slot/module

notation. Unlimited number of

locations.

location node-id

Command Default

No correlation rule sets are applied.

Command Modes

Global configuration

Command History

Modification

Release

This command was introduced.

Release 3.6.0

Usage Guidelines

The

logging correlator apply ruleset

command is used to either add or remove apply settings for a given

rule set. These settings then determine which messages are correlated for the affected rules.

If the rule set is applied to

all-of-router

, then correlation occurs for only those messages that match the

configured cause values for the rule to be correlated, regardless of the context or location setting of that
message.

If a rule set is applied to a specific set of contexts or locations, then correlation occurs for only those messages
that match both the configured cause values for the rule and at least one of those contexts or locations.

Use the

show logging correlator ruleset, on page 55

command to show the current apply settings for a given

rule set.

Cisco IOS XR System Monitoring Command Reference for the Cisco XR 12000 Series Router, Release 4.1

18

OL-24735-01

Alarm Management and Logging Correlation Commands

logging correlator apply ruleset

«
...
28
29
30
31
32
...
»

Summary of Contents for XR 1200 series

















































































































































































































































































































































































































































Reviews:

No comments

Related manuals for XR 1200 series

Brand: D-Link Pages: 176

Brand: Juniper Pages: 502

Brand: LogLogic Pages: 30

Brand: Mercusys Pages: 35

Brand: Teknim Pages: 10

Brand: Ruckus Wireless Pages: 2

Brand: Rosewill Pages: 10

Brand: TP-Link Pages: 2

Brand: Moxa Technologies Pages: 51

AlterPath Manager 2500

Brand: Cyclades Pages: 368

Brand: ADTRAN Pages: 4

NVR2104/2108HS-W-4KS2 1U

Brand: Dahua Technology Pages: 363

Brand: ADTRAN Pages: 20

AirBridge VS-YOFIMN-000

Brand: Vivint Pages: 2

Brand: LevelOne Pages: 83

Brand: Westermo Pages: 22

Brand: Brickcom Pages: 184

EdgeRouter X ER-X-SFP

Brand: Ubiquiti Pages: 20

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands