Cisco XR 1200 series Command Reference Manual Download Page 374

Page: 374 / 432

monitor controller fabric

To monitor controller fabric counters in real time, use the

monitor controller fabric

command in EXEC

mode.

monitor controller fabric

{

plane-id| all

}

Syntax Description

Plane ID number of the fabric plane to be monitored. The range is 0 to 7.

plane-id

Monitors all fabric planes.

all

Command Default

None

Command Modes

EXEC

Command History

Modification

Release

This command was introduced.

Release 3.2

Usage Guidelines

Use the

monitor controller fabric

command to display controller fabric counters. The display refreshes

every 2 seconds.

The interactive commands that are available during a controller fabric monitoring session are described in
this table.

Table 33: Interactive Commands Available for the monitor controller fabric Command

Description

Command

Resets controller fabric counters to 0.

Freezes the display screen, thereby suspending the
display of fresh counters.

Thaws the display screen, thereby resuming the
display of fresh counters.

Terminates the controller fabric monitoring session.

Enables you to jump to a nonsequential fabric plane.
You are prompted to enter the plane ID of the fabric
to be monitored.

Cisco IOS XR System Monitoring Command Reference for the Cisco XR 12000 Series Router, Release 4.1

362

OL-24735-01

Performance Management Commands

monitor controller fabric

Summary of Contents for XR 1200 series

















































































































































































































































































































































































































































Search results

Summary of Contents for XR 1200 series

Reviews:

Related manuals for XR 1200 series

Brands by name

Popular brands

Cisco XR 1200 series, Command Reference Manual

Search results

Summary of Contents for XR 1200 series

Reviews:

Related manuals for XR 1200 series

Brands by name

Popular brands