Cisco XR 1200 series Command Reference Manual Download Page 144

Page: 144 / 432

destination port

To identify the port of the target device, use the

destination port

command in the appropriate configuration

mode. To unset the destination port, use the

form of this command.

destination port port

no destination port

Syntax Description

Port number of the target device. Range is 1 to 65355.

port

Command Default

None

Command Modes

IP SLA UDP echo configuration

IP SLA UDP jitter configuration

Command History

Modification

Release

This command was introduced.

Release 3.3.0

Usage Guidelines

The

destination port

command is not supported when you configure an ICMP operation; it is supported only

to configure UDP operations.

You must specify the port of the target device. The configuration for the

destination port

command is

mandatory for both IP SLA UDP echo and IP SLA UDP jitter configurations.

Task ID

Operations

Task ID

read, write

monitor

Examples

The following example shows how to designate a port for the

destination port

command in IP SLA UDP

jitter configuration mode:

RP/0/0/CPU0:router#

configure

RP/0/0/CPU0:router(config)#

ipsla

RP/0/0/CPU0:router(config-ipsla)#

operation 1

RP/0/0/CPU0:router(config-ipsla-op)#

type udp jitter

RP/0/0/CPU0:router(config-ipsla-udp-jitter)#

destination port 11111

Cisco IOS XR System Monitoring Command Reference for the Cisco XR 12000 Series Router, Release 4.1

132

OL-24735-01

IP Service Level Agreement Commands

destination port

Summary of Contents for XR 1200 series

















































































































































































































































































































































































































































Search results

Summary of Contents for XR 1200 series

Reviews:

Related manuals for XR 1200 series

Brands by name

Popular brands

Cisco XR 1200 series, Command Reference Manual

Search results

Summary of Contents for XR 1200 series

Reviews:

Related manuals for XR 1200 series

Brands by name

Popular brands