Cisco XR 1200 series Command Reference Manual Download Page 376

Page: 376 / 432

monitor controller sonet

To monitor SONET controller counters, use the

monitor controller sonet

command in EXEC mode.

monitor controller sonet interface-path-id

Syntax Description

Physical interface or virtual interface.

Use the

show interfaces

command to see a list of all interfaces currently

configured on the router.

Note

For more information about the syntax for the router, use the question mark (

)

online help function.

interface-path-id

Command Modes

EXEC

Command History

Modification

Release

This command was introduced.

Release 3.2

Usage Guidelines

Use the

monitor controller sonet

command to display SONET controller counters. The display refreshes

every 2 seconds.

The interactive commands that are available during a controller monitoring session are described in this table.

Table 34: Interactive Commands for the monitor controller sonet Command

Description

Command

Resets controller SONET counters to 0.

Freezes the display screen, thereby suspending the
display of fresh counters.

Thaws the display screen, thereby resuming the
display of fresh counters.

Terminates the controller SONET monitoring session.

Enables you to jump to a nonsequential SONET
controller. You are prompted to enter the
SONETcontroller to be monitored.

Cisco IOS XR System Monitoring Command Reference for the Cisco XR 12000 Series Router, Release 4.1

364

OL-24735-01

Performance Management Commands

monitor controller sonet

Summary of Contents for XR 1200 series

















































































































































































































































































































































































































































Search results

Summary of Contents for XR 1200 series

Reviews:

Related manuals for XR 1200 series

Brands by name

Popular brands

Cisco XR 1200 series, Command Reference Manual

Search results

Summary of Contents for XR 1200 series

Reviews:

Related manuals for XR 1200 series

Brands by name

Popular brands