Cisco XR 1200 series Command Reference Manual Download Page 229

Page: 229 / 432

schedule period

To configure the amount of time during which all LSP operations are scheduled to start or run, use the

schedule

period

command in IP SLA MPLS LSP monitor schedule configuration mode. To remove the scheduler, use

the

form of this command.

schedule period seconds

no schedule period

Syntax Description

Amount of time in seconds for which label switched path (LSP) operations are
scheduled to run. Range is 1 to 604800.

seconds

Command Default

None

Command Modes

IP SLA MPLS LSP monitor schedule configuration

Command History

Modification

Release

This command was introduced.

Release 3.5.0

Usage Guidelines

Use the

schedule period

command to specify the amount of time in seconds during which all LSP operations

are scheduled to start running. All LSP operations are scheduled equally spaced throughout the schedule
period.

For example, if the schedule period is 600 seconds and there are 60 operations to be scheduled, they are
scheduled at 10-second intervals.

Use the

frequency

command to specify how often the entire set of operations is performed. The frequency

value must be greater than or equal to the schedule period.

You must configure the schedule period before you can start MPLS LSP monitoring. Start MPLS LSP
monitoring using the

start-time

command.

Task ID

Operations

Task ID

read, write

monitor

Cisco IOS XR System Monitoring Command Reference for the Cisco XR 12000 Series Router, Release 4.1

OL-24735-01

217

IP Service Level Agreement Commands

schedule period

Summary of Contents for XR 1200 series

















































































































































































































































































































































































































































Search results

Summary of Contents for XR 1200 series

Reviews:

Related manuals for XR 1200 series

Brands by name

Popular brands

Cisco XR 1200 series, Command Reference Manual

Search results

Summary of Contents for XR 1200 series

Reviews:

Related manuals for XR 1200 series

Brands by name

Popular brands