Cisco XR 1200 series Command Reference Manual Download Page 250 | Manualshive

Page: 250 / 432

background image

show ipsla statistics aggregated

To display the hourly statistics for all the IP SLA operations or specified operation, use the

show ipsla statistics

aggregated

command in EXEC mode.

show ipsla statistics aggregated [detail]

[

operation-number

]

Syntax Description

Displays detailed information.

detail

(Optional) Number of IP SLA operations. Range is 1 to 2048.

operation-number

Command Default

None

Command Modes

EXEC

Command History

Modification

Release

This command was introduced.

Release 3.3.0

Show output was expanded to include detailed information when path
discovery is enabled.

Release 3.6.0

Usage Guidelines

The

show ipsla statistics aggregated

command displays information such as the number of failed operations

and the reason for failure. Unless you configured a different amount of time for the

buckets

command (

statistics

command with

hourly

keyword), the

show ipsla statistics aggregated

command displays the information

collected over the past two hours.

For one-way delay and jitter operations to be computed for UDP jitter operations, the clocks on local and
target devices must be synchronized using NTP or GPS systems. If the clocks are not synchronized, one-way
measurements are discarded. If the sum of the source to destination (SD) and the destination to source (DS)
values is not within 10 percent of the round-trip time, the one-way measurement values are assumed to be
faulty, and are discarded.

Task ID

Operations

Task ID

read

monitor

Cisco IOS XR System Monitoring Command Reference for the Cisco XR 12000 Series Router, Release 4.1

238

OL-24735-01

IP Service Level Agreement Commands

show ipsla statistics aggregated

«
...
248
249
250
251
252
...
»

Summary of Contents for XR 1200 series

















































































































































































































































































































































































































































Reviews:

No comments

Related manuals for XR 1200 series

Brand: D-Link Pages: 15

DSN-4100 Series

Brand: D-Link Pages: 2

Brand: D-Link Pages: 2

Brand: Parker Pages: 344

DHI-NVR5224-24P-4KS2

Brand: Dahua Pages: 24

Brand: Allied Telesis Pages: 1

Brand: Macsense Pages: 39

Brand: Valcom Pages: 4

Brand: Caton Pages: 18

SW-UNM-24FE2GC-24POE

Brand: Morrell Pages: 8

SmartSTACK ELS100-24TXM

Brand: Cabletron Systems Pages: 117

PacketMate 1000

Brand: General DataComm Pages: 20

Brand: Vacron Pages: 16

D-Link DSL-2640U

Brand: Broadband Products Pages: 12

AirStation G54 WLA2-G54

Brand: Buffalo Pages: 8

Brand: ADTRAN Pages: 20

Brand: MiLAN Pages: 155

Brand: Planet Pages: 67

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands