Cisco XR 1200 series Command Reference Manual Download Page 219

Page: 219 / 432

reply mode

To specify how to reply to echo requests, use the

reply mode

command in the appropriate configuration mode.

To return to the default value, use the

form of this command.

reply mode

{

control-channel| router-alert

}

no reply mode

Syntax Description

Sets echo requests to reply by way of a control channel.

This option is available only in IP SLA MPLS LSP ping configuration
mode.

Note

control-channel

Sets echo requests to reply as an IPv4 UDP packet with IP router alert.

router-alert

Command Default

The default reply mode for an echo request packet is an IPv4 UDP packet without IP router alert set.

Command Modes

IP SLA MPLS LSP ping configuration

IP SLA MPLS LSP trace configuration

IP SLA MPLS LSP monitor ping configuration

IP SLA MPLS LSP monitor trace configuration

Command History

Modification

Release

This command was introduced.

Release 3.4.0

This command was added to IP SLA MPLS LSP monitor ping and monitor
trace configuration modes.

The

control-channel

keyword was added in IP SLA MPLS LSP ping

configuration mode.

Release 3.5.0

Usage Guidelines

Use the

reply mode

command with the

control-channel

keyword to send echo reply packets by way of a

control channel in an MPLS LSP ping operation. If the target is not set to pseudowire, the configuration of
the

control-channel

keyword is rejected. Refer to the

target pseudowire

command for information about

setting the target.

Use the

reply mode

command with the

router-alert

keyword to set the reply mode of echo reply packets in

an MPLS LSP ping or MPLS LSP trace operation. After you enter this command, echo reply packets are set
to reply as an IPv4 UDP packet with the IP router alert option in the UDP packet header.

Cisco IOS XR System Monitoring Command Reference for the Cisco XR 12000 Series Router, Release 4.1

OL-24735-01

207

IP Service Level Agreement Commands

reply mode

Summary of Contents for XR 1200 series

















































































































































































































































































































































































































































Search results

Summary of Contents for XR 1200 series

Reviews:

Related manuals for XR 1200 series

Brands by name

Popular brands

Cisco XR 1200 series, Command Reference Manual

Search results

Summary of Contents for XR 1200 series

Reviews:

Related manuals for XR 1200 series

Brands by name

Popular brands