Cisco XR 1200 series Command Reference Manual Download Page 174

Page: 174 / 432

lsr-path

To specify a loose source routing path in which to measure the ICMP, use the

lsr-path

command in the

appropriate configuration mode. To use a path other than the specified one, use the

form of this command.

lsr-path ipaddress1

[

ipaddress2

[...

[ipaddress8]

]]

no lsr-path

Syntax Description

IPv4 address of the intermediate node. Up to eight addresses can be entered.

ip address

Command Default

No path is configured.

Command Modes

IP SLA ICMP path-jitter configuration

IP SLA ICMP path-echo configuration

Command History

Modification

Release

This command was introduced.

Release 3.3.0

Usage Guidelines

The

lsr-path

command applies only to ICMP path-echo and ICMP path-jitter operation types.

You can configure up to a maximum of eight hop addresses by using the

lsr-path

command, as shown in the

following example:

lsr-path ipaddress1 [ipaddress2 [... [ipaddress8]]]

Task ID

Operations

Task ID

read, write

monitor

Examples

The following example shows how to use the

lsr-path

command in IP SLA ICMP Path-echo configuration

mode:

RP/0/0/CPU0:router#

configure

RP/0/0/CPU0:router(config)#

ipsla

RP/0/0/CPU0:router(config-ipsla)#

operation 1

RP/0/0/CPU0:router(config-ipsla-op)#

type icmp path-echo

RP/0/0/CPU0:router(config-ipsla-icmp-path-echo)#

lsr-path 192.0.2.40

Cisco IOS XR System Monitoring Command Reference for the Cisco XR 12000 Series Router, Release 4.1

162

OL-24735-01

IP Service Level Agreement Commands

lsr-path

Summary of Contents for XR 1200 series

















































































































































































































































































































































































































































Search results

Summary of Contents for XR 1200 series

Reviews:

Related manuals for XR 1200 series

Brands by name

Popular brands

Cisco XR 1200 series, Command Reference Manual

Search results

Summary of Contents for XR 1200 series

Reviews:

Related manuals for XR 1200 series

Brands by name

Popular brands