Cisco XR 1200 series Command Reference Manual Download Page 309

Page: 309 / 432

vrf (IP SLA MPLS LSP monitor)

To specify which virtual routing and forwarding instance (VRF) is monitored in an IP SLA MPLS LSP monitor
ping or trace, use the

vrf

command in the the appropriate configuration mode. To revert to the monitoring of

all VRFs, use the

form of this command.

vrf vrf-name

no vrf

Syntax Description

Name of the VRF. Maximum length is 32 alphanumeric characters.

vrf-name

Command Default

All VRFs are monitored.

Command Modes

IP SLA MPLS LSP monitor ping configuration

IP SLA MPLS LSP monitor trace configuration

Command History

Modification

Release

This command was introduced.

Release 3.5.0

Usage Guidelines

The

vrf

command in IP SLA MPLS LSP monitor configuration mode specifies to monitor a specific VRF in

ping and trace operations. The default is that all VRFs are monitored.

Task ID

Operations

Task ID

read, write

monitor

Examples

The following example shows how to use the

vrf

command in IP SLA MPLS LSP monitor configuration

mode:

RP/0/0/CPU0:router#

configure

RP/0/0/CPU0:router(config)#

ipsla

RP/0/0/CPU0:router(config-ipsla)#

mpls lsp-monitor

RP/0/0/CPU0:router(config-ipsla-mplslm)#

monitor 2

RP/0/0/CPU0:router(config-ipsla-mplslm-def)#

type mpls lsp trace

RP/0/0/CPU0:router(config-ipsla-mplslm-lsp-trace)#

vrf vpn-lsp

Cisco IOS XR System Monitoring Command Reference for the Cisco XR 12000 Series Router, Release 4.1

OL-24735-01

297

IP Service Level Agreement Commands

vrf (IP SLA MPLS LSP monitor)

Summary of Contents for XR 1200 series

















































































































































































































































































































































































































































Search results

Summary of Contents for XR 1200 series

Reviews:

Related manuals for XR 1200 series

Brands by name

Popular brands

Cisco XR 1200 series, Command Reference Manual

Search results

Summary of Contents for XR 1200 series

Reviews:

Related manuals for XR 1200 series

Brands by name

Popular brands