Cisco XR 1200 series Command Reference Manual Download Page 169

Page: 169 / 432

RP/0/0/CPU0:router(config-ipsla-udp-echo)#

history

RP/0/0/CPU0:router(config-ipsla-op-hist)#

lives 2

Related Commands

Description

Command

Sets the number of history buckets that are kept during
the lifetime of the IP SLA operation.

buckets (history), on page 121

Defines the type of information that are kept in the
history table for the IP SLA operation.

filter, on page 140

Configures an IP SLA operation.

operation, on page 174

Schedules an IP SLA operation.

schedule operation, on page 215

Cisco IOS XR System Monitoring Command Reference for the Cisco XR 12000 Series Router, Release 4.1

OL-24735-01

157

IP Service Level Agreement Commands

lives

Summary of Contents for XR 1200 series

















































































































































































































































































































































































































































Search results

Summary of Contents for XR 1200 series

Reviews:

Related manuals for XR 1200 series

Brands by name

Popular brands

Cisco XR 1200 series, Command Reference Manual

Search results

Summary of Contents for XR 1200 series

Reviews:

Related manuals for XR 1200 series

Brands by name

Popular brands