Cisco XR 1200 series Command Reference Manual Download Page 140

Page: 140 / 432

datasize request

To set the protocol data size in the request packet in the payload of an operation, use the

datasize request

command in the appropriate configuration mode. To reset the default data size, use the

form of this

command.

datasize request size

no datasize request

Syntax Description

Specifies the following ranges and default values that are protocol dependent:

•

For a UDP jitter operation, range is 16 to 1500 B.

•

For a UDP echo operation, range is 4 to 1500 B.

•

For an ICMP echo operation, range is 0 to 16384 B.

•

For an ICMP path-echo operation, range is 0 to 16384 B.

•

For an ICMP path-jitter operation, range is 0 to 16384 B.

•

For an MPLS LSP ping operation, range is 100 to 17986 B.

size

Command Default

For a UDP jitter operation, the default value is 32 B.

For a UDP echo operation, the default value is 16 B.

For an ICMP echo operation, the default value is 36 B.

For an ICMP path-echo operation, the default value is 36 B.

For an ICMP path-jitter operation, the default value is 36 B.

For an MPLS LSP ping operation, the default value is 100 B.

Command Modes

IP SLA UDP echo configuration

IP SLA UDP jitter configuration

IP SLA ICMP path-jitter configuration

IP SLA ICMP path-echo configuration

IP SLA ICMP echo configuration

IP SLA MPLS LSP ping configuration

Command History

Modification

Release

This command was introduced.

Release 3.3.0

Cisco IOS XR System Monitoring Command Reference for the Cisco XR 12000 Series Router, Release 4.1

128

OL-24735-01

IP Service Level Agreement Commands

datasize request

Summary of Contents for XR 1200 series

















































































































































































































































































































































































































































Search results

Summary of Contents for XR 1200 series

Reviews:

Related manuals for XR 1200 series

Brands by name

Popular brands

Cisco XR 1200 series, Command Reference Manual

Search results

Summary of Contents for XR 1200 series

Reviews:

Related manuals for XR 1200 series

Brands by name

Popular brands