Cisco XR 1200 series Command Reference Manual Download Page 361

Page: 361 / 432

Table 32: show logging history Field Descriptions

Description

Field

Number of messages that can be stored in the history
table. Set with the

logging history size

command.

maximum table entries

Level of messages that are stored in the history table
and sent to the SNMP server (if SNMP notifications
are enabled). Set with the

logging history

command.

saving level

Number of messages not stored in the history table
because the severity level is greater than that specified
with the

logging history

command.

messages ignored

Status of whether syslog traps of the appropriate level
are sent to the SNMP server. Syslog traps are either
enabled or disabled through the

snmp-server enable

command.

SNMP notifications

Related Commands

Description

Command

Changes the severity level of syslog messages stored
in the history file and sent to the SNMP server.

logging history, on page 325

Changes the number of syslog messages that can be
stored in the history table.

logging history size, on page 327

Cisco IOS XR System Monitoring Command Reference for the Cisco XR 12000 Series Router, Release 4.1

OL-24735-01

349

Logging Services Commands

show logging history

Summary of Contents for XR 1200 series

















































































































































































































































































































































































































































Search results

Summary of Contents for XR 1200 series

Reviews:

Related manuals for XR 1200 series

Brands by name

Popular brands

Cisco XR 1200 series, Command Reference Manual

Search results

Summary of Contents for XR 1200 series

Reviews:

Related manuals for XR 1200 series

Brands by name

Popular brands