Cisco XR 1200 series Command Reference Manual Download Page 66

Page: 66 / 432

Description

Field

Indicates whether or not the rule has been applied. If
the rule applies to the entire router, this field will
display

“

RULE_APPLIED_ALL.

”

Rule State

Message category, group, and code.

Code Type

Message category, group and code of the root message
configured in the logging correlation rule.

Root

Message category, group and code of a non-root-cause
message configured in the logging correlation rule.

Leaf

Node or nodes where the rule is applied. If the logging
correlation rule applies to the entire router, this field
will display

“

None.

”

Apply Locations

Context or contexts to which the rule is applied. If
the logging correlation rule is not configured to apply
to a context, this field will display

“

None.

”

Apply Contexts

Related Commands

Description

Command

Applies and activates correlation rules.

logging correlator apply rule, on page 15

Defines the rules for correlating messages.

logging correlator rule, on page 22

Displays messages in the logging correlator buffer.

show logging correlator buffer, on page 47

Displays the logging correlator buffer size and the
percentage of the buffer occupied by correlated
messages

show logging correlator info, on page 50

Cisco IOS XR System Monitoring Command Reference for the Cisco XR 12000 Series Router, Release 4.1

OL-24735-01

Alarm Management and Logging Correlation Commands

show logging correlator rule

Summary of Contents for XR 1200 series

















































































































































































































































































































































































































































Search results

Summary of Contents for XR 1200 series

Reviews:

Related manuals for XR 1200 series

Brands by name

Popular brands

Cisco XR 1200 series, Command Reference Manual

Search results

Summary of Contents for XR 1200 series

Reviews:

Related manuals for XR 1200 series

Brands by name

Popular brands