Cisco XR 1200 series Command Reference Manual Download Page 406

Page: 406 / 432

Description

Attributes

Entity

Address messages received.

AddressMsgsRcvd

mpls ldp

Address messages sent.

AddressMsgsSent

Address withdraw messages
received.

AddressWithdrawMsgsRcvd

Address withdraw messages sent.

AddressWithdrawMsgsSent

Initial messages sent.

InitMsgsSent

Initial messages received.

InitMsgsRcvd

Keepalive messages received.

KeepaliveMsgsRcvd

Keepalive messages sent.

KeepaliveMsgsSent

Label mapping messages received.

LabelMappingMsgsRcvd

Label mapping messages sent.

LabelMappingMsgsSent

Label release messages received.

LabelReleaseMsgsRcvd

Label release messages sent.

LabelReleaseMsgsSent

Label withdraw messages received.

LabelWithdrawMsgsRcvd

Label withdraw messages sent.

LabelWithdrawMsgsSent

Notification messages received.

NotificationMsgsRcvd

Notification messages sent.

NotificationMsgsSent

Total messages received.

TotalMsgsRcvd

Total messages sent.

TotalMsgsSent

Average system percent CPU
utilization.

AverageCPUUsed

node cpu

Number of processes.

NoProcesses

Current application memory (in
bytes) in use.

CurrMemory

node memory

Maximum system memory (in MB)
used since bootup.

PeakMemory

Cisco IOS XR System Monitoring Command Reference for the Cisco XR 12000 Series Router, Release 4.1

394

OL-24735-01

Performance Management Commands

performance-mgmt thresholds

Summary of Contents for XR 1200 series

















































































































































































































































































































































































































































Search results

Summary of Contents for XR 1200 series

Reviews:

Related manuals for XR 1200 series

Brands by name

Popular brands

Cisco XR 1200 series, Command Reference Manual

Search results

Summary of Contents for XR 1200 series

Reviews:

Related manuals for XR 1200 series

Brands by name

Popular brands