Cisco XR 1200 series Command Reference Manual Download Page 380 | Manualshive

Page: 380 / 432

background image

Enables you to jump to a nonsequential interface. You
are prompted to enter the interface type and interface
path ID to be monitored.

i

Displays the previous sequential interface in the list
of available interfaces.

p

Displays the next sequential interface in the list of
available interfaces.

n

Terminates the interface monitoring session.

q

Task ID

Operations

Task ID

execute

basic-services

read

monitor

Examples

When more than one interface is specified, the statistics for each interface are displayed on a separate line.
This display format appears anytime more than one interface is specified. For example:

•

To display statistics for all interfaces, enter the command

monitor interface

.

•

To display all the interfaces for an interface type, such as all POS interface, enter the command and
wildcard

monitor interface pos *

.

•

To display statistics for three specified interfaces, enter the command

monitor interface pos0/2/0/0

pos0/5/0/1 pos0/5/0/2

.

This is the sample output for the

monitor interface

command entered without an argument. This command

displays statistics for all interfaces in the system.

RP/0/0/CPU0:router#

monitor interface

Protocol:General

Rack6-1 Monitor Time: 00:00:01 SysUptime: 165:52:41 Interface In(bps) Out(bps)

InBytes/Delta OutBytes/Delta Mg0/0/CPU0/0 1500/ 0% 7635/ 0% 58.4M/420 8.1M/2138

PO0/4/0/0 578/ 0% 535/ 0% 367.2M/162 377.5M/150 PO0/4/0/1 278/ 0% 0/ 0% 345.7M/78

360.1M/0 Gi0/5/0/1 3128/ 0% 2171/ 0% 382.8M/876 189.1M/608 Gi0/5/0/1.1 0/ 0%

0/ 0%

824.6G/0 1.0T/0 Gi0/5/0/1.2 0/ 0% 0/ 0% 1.0T/0 824.6G/0 Gi0/5/0/1.3 678/ 0% 0/

0%

1.0T/190 1.0T/0 Gi0/5/0/1.4 0/ 0% 0/ 0% 824.6G/0 824.6G/0 Gi0/5/0/1.5 0/ 0%

350/ 0%

824.6G/0 1.0T/98 Gi0/5/0/1.6 327/ 0% 348/ 0% 824.6G/92 1.0T/98 Gi0/5/0/1.7 0/

0% 346/ 0%

824.6G/0 1.0T/98 Gi0/5/0/1.8 325/ 0% 0/ 0% 824.6G/92 1.0T/0 Quit='q', Clear='c',

Freeze='f', Thaw='t', Next set='n', Prev set='p', Bytes='y', Packets='k'

(General='g',

IPv4 Uni='4u', IPv4 Multi='4m', IPv6 Uni='6u', IPv6 Multi='6m') Rack6-1 Monitor

Time:

00:00:01 SysUptime: 165:52:41 Protocol:IPv4 Unicast Interface In(bps) Out(bps)
InBytes/Delta OutBytes/Delta Mg0/0/CPU0/0 0/ 0% 0/ 0% 85.3M/0 6.9M/0 PO0/4/0/0

Cisco IOS XR System Monitoring Command Reference for the Cisco XR 12000 Series Router, Release 4.1

368

OL-24735-01

Performance Management Commands

monitor interface

«
...
378
379
380
381
382
...
»

Summary of Contents for XR 1200 series

















































































































































































































































































































































































































































Reviews:

No comments

Related manuals for XR 1200 series

Brand: D-Link Pages: 5

Brand: D-Link Pages: 2

Brand: Qlogic Pages: 2

Brand: Qlogic Pages: 172

Brand: XMOS Pages: 6

Marconi OMS 1200

Brand: Ericsson Pages: 136

Brand: National Instruments Pages: 130

Brand: MiWire Pages: 24

Brand: LaView Pages: 2

Dynalink MyZone 3G24W

Brand: NetComm Pages: 5

Brand: Alcatel-Lucent Pages: 154

Brand: ENKHO Pages: 48

Brand: Brickcom Pages: 184

Brand: WatchNet Pages: 2

Brand: l-com Pages: 11

Turbo 16/4 Token-Ring PC Card 2

Brand: IBM Pages: 123

Brand: Billion Pages: 2

Brand: Cambium Networks Pages: 672

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands