Cisco XR 1200 series Command Reference Manual Download Page 146 | Manualshive

Page: 146 / 432

background image

distribution count

To set the number of statistics distributions that are kept for each hop during the lifetime of the IP SLA
operation, use the

distribution count

command in IP SLA operation statistics configuration mode. To use

the default value, use the

no

form of this command.

distribution count slot

no distribution count

Syntax Description

Number of statistics distributions that are kept. Range is 1 to 20. Default is 1.

slot

Command Default

The default value is 1.

Command Modes

IP SLA operation statistics configuration

Command History

Modification

Release

This command was introduced.

Release 3.3.0

Usage Guidelines

In most situations, you do not need to change the number of statistics distributions kept or the time interval
for each distribution. Only change these parameters when distributions are needed, for example, when
performing statistical modeling of your network. To set the statistics distributions interval, use the

distribution

interval

command in IP SLA operation statistics configuration mode. The total number of statistics distributions

captured is the value set by the

distribution count

command times the value set by the

maximum hops

command times the value set by the

maximum path

command times the value set by the

buckets

command.

Task ID

Operations

Task ID

read, write

monitor

Examples

The following example shows how to set the number of statistics distribution for the

distribution count

command:

RP/0/0/CPU0:router#

configure

RP/0/0/CPU0:router(config)#

ipsla

RP/0/0/CPU0:router(config-ipsla)#

operation 1

RP/0/0/CPU0:router(config-ipsla-op)#

type udp jitter

RP/0/0/CPU0:router(config-ipsla-udp-jitter)#

statistics hourly

RP/0/0/CPU0:router(config-ipsla-op-stats)#

distribution count 15

Cisco IOS XR System Monitoring Command Reference for the Cisco XR 12000 Series Router, Release 4.1

134

OL-24735-01

IP Service Level Agreement Commands

distribution count

«
...
144
145
146
147
148
...
»

Summary of Contents for XR 1200 series

















































































































































































































































































































































































































































Reviews:

No comments

Related manuals for XR 1200 series

Brand: Cambium Networks Pages: 68

Brand: Cambium Networks Pages: 110

Brand: ICP DAS USA Pages: 8

Brand: TP-Link Pages: 2

Brand: ZyXEL Communications Pages: 2

Brand: Dahua Pages: 24

Proventia A1204

Brand: Internet Security Systems Pages: 42

SUPERLOADER DLT MAGAZINE

Brand: Tandberg Data Pages: 6

8677 - BladeCenter Rack-mountable - Power Supply

Brand: IBM Pages: 126

Brand: Xenya Pages: 189

Brand: B+B SmartWorx Pages: 52

Easy Tool-ID BSG TID-05-T30-00-005

Brand: Balluff Pages: 46

memonizerWORKSTATION

Brand: MEMON Pages: 2

Brand: TP-Link Pages: 176

Brand: eWON Pages: 34

SW-UNM-24FE2GC-24POE

Brand: Morrell Pages: 8

Brand: ICP DAS USA Pages: 8

LMP-1202G-SFP Series

Brand: ANTAIRA Pages: 19

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands