B&R ACOPOSinverter P84, User Manual

Page: 59 / 405

Installation guide
ACOPOSinverter P84 User's Manual 2.10 59
Model number 8I84T403700.01P-1 8I84T404500.01P-1 8I84T405500.01P-1 8I84T407500.01P-1
Input impedance
Voltage 30 kΩ
Current 242 Ω
Relay outputs
Quantity 2
Nominal voltage 30 VDC / 250 VAC
Switching capacity
Min. 3 mA for 24 VDC
Max.
With resistive load (cos φ = 1
and L/R = 0 ms)
2 A for 250 VAC or 30 VDC
With inductive load (cos φ = 0.4
and L/R = 7 ms)
1.5 A for 250 VAC or 30 VDC
Design
Relay 1 1 NO contact and 1 NC contact with a common point
Relay 2 1 NO contact
Response time (max.) <7 ms ±0.5 ms
Electrical isolation
Output - ACOPOSinverter Yes
Output - Output No
Analog outputs
Quantity 1
Output 0 to 10 V or 0 to 20 mA
8)
Electrical isolation
Output - ACOPOSinverter Yes
Output - Output No
Max. load impedance
Voltage 470 Ω
Current 500 Ω
Update time <2 ms ±0.5 ms
Resolution 10-bit
Operating conditions
Installation at elevations above sea
level
0 to 1000 m
Degree of protection per EN 60529 Upper part: IP21 and IP41
Lower part: IP54 (heat sink)
Ambient temperature -10 to 50°C
Max. ambient temperature Up to 60°C
Relative humidity per IEC 60068-2-3 5 to 95%, non-condensing
No dripping water
Maximum installation elevation Up to 3000 m
9)
Max. pollution degree per IEC/EN
61800-5-1
2 (non-conductive pollution)
Environmental conditions per IEC
60721-3-3
Class 3C1 and 3S2
Operating position Vertical mounting orientation ±10%
Environmental conditions
Temperature
Storage -25 to 70°C
Vibration
Operation 3 to 13 Hz: 1.5 mm amplitude / 13 to 200 Hz: 1 g
Shock
Operation 15 g, 11 ms
Mechanical characteristics
Dimensions
Width 240 mm 320 mm
Height 550 mm 630 mm
Depth 266 mm 290 mm
Weight 37 kg 45 kg
Table 18: 8I84T403700.01P-1, 8I84T404500.01P-1, 8I84T405500.01P-1, 8I84T407500.01P-1 - Technical data
1) Shield plate included in delivery
2) For shielded motor cables
≤50 m → At a clock frequency of 2 to 2.5 kHz
≤25 m → At a clock frequency of 2.6 to 12 kHz
3) For shielded motor cables
≤100 m → At a clock frequency of 2 to 2.5 kHz and at a clock frequency of 2.6 to 12 kHz
4) For shielded motor cables
≤300 m → At a clock frequency of 2 to 2.5 kHz
≤200 m → At a clock frequency of 2.6 to 12 kHz
5) These values are valid for the rated clock frequency.
6) The min. resistance value is specified at a temperature of 20°C.
7) 1 logic input, configurable as a logic input or PTC sensor input using a switch. Input for max. 6 PTC sensors in series: Nominal value <1.5 kΩ, 3 kΩ trigger
resistance, 1.8 kΩ reset value, short-circuit proof <50 Ω
8) The analog output is configurable as a logic output.
9) From 1000 to 3000 m, current reduced by 1% per 100 m