Proximus Forum 500 Series Скачать руководство пользователя страница 327

Страница: 327 / 348

General/Hardware

Frequently Asked Questions

325

Frequently Asked Questions

This chapter provides tips and information on how to deal with any
malfunctions or faults you may experience with the Forum 5004/5008/
5012.

Please note:

Repairs to the Forum 5004/5008/5012 should only be carried
out by qualified personnel.

The following LEDs indicate that the Forum 5004/5008/5012 is ready for
operation (see also

LED Display on a Hardware Unit

starting on page 43):

Position of LEDs on the Forum 5004/5008/5012

General/Hardware

Question: The Forum 5004/5008/5012 is not functioning.

Make sure the mains plug is properly connected.

Plug another device into the mains socket to check whether there is any
voltage.

Question: The mains plug is connected, the mains socket is supplying
output, but the Forum 5004/5008/5012 still does not function.

DANGER!

This device contains hazardous voltages. To make the
system dead, remove the power plug from the socket.

Is the power LED illuminated?

If not, contact your service centre. The AC adapter plug of the Forum 5004/
5008/5012 may be defective.

LAN LED

LEDs (rack version)

LEDs (wall version)

LAN 1

LAN 2

Ready LED

Power LED

Ready LED

Power LED

LAN LED

LAN 2

LAN 1

Содержание Forum 500 Series





























































































































































































































































































































































Результаты поиска

Содержание Forum 500 Series

Отзывы:

Похожие инструкции для Forum 500 Series

Бренды по названию

Популярные бренды

Proximus Forum 500 Series, Руководство по монтажу и пусконаладке

Результаты поиска

Содержание Forum 500 Series

Отзывы:

Похожие инструкции для Forum 500 Series

Бренды по названию

Популярные бренды