Proximus Forum 500 Series Скачать руководство пользователя страница 132

Страница: 132 / 348

Forum Gateway 560 Modules

130

Forum 550 Card 8 analogue extensions: LEDs

The LEDs indicate the following:

Operational information

The Forum 550 Card 8 analogue extensions interface card can be exchanged
during operation. However, the slot must first be deactivated in the

Configurator

in the web console (see

Installing Interface Cards

starting on

page 97).

Forum 550 Media Gateway Card

Field of application

The Forum 550 Media Gateway Card interface card provides 16 media
gateway channels for VoIP.

LED 1:

Constantly yellow

At least one connection established
through the interface card is active.

LED 2:

Constantly green

The interface card is operational; the slot
has been activated (flickering is normal).

Flashing yellow

The interface card is ready, but the slot
has not been activated or the interface
card has not been configured yet.

Constantly red

New software is being loaded onto the
interface card. If the LED lights up red for
an extended period of time, there may
be a fault.

LED 3:

–

Not used

LED 4:

–

Not used

a/b 1

a/b 2

MS+A1-8

1
2

3
4

Содержание Forum 500 Series





























































































































































































































































































































































Результаты поиска

Содержание Forum 500 Series

Отзывы:

Похожие инструкции для Forum 500 Series

Бренды по названию

Популярные бренды

Proximus Forum 500 Series, Руководство по монтажу и пусконаладке

Результаты поиска

Содержание Forum 500 Series

Отзывы:

Похожие инструкции для Forum 500 Series

Бренды по названию

Популярные бренды