Proximus Forum 500 Series Скачать руководство пользователя страница 125 | Manualshive

Страница: 125 / 348

background image

Forum Gateway 560 Modules

123

●

A maximum of four Forum 550 Card PRA interface cards can be
configured in the entire system.

●

No settings need to be made on the Forum 550 Card PRA interface card.

●

The Forum 550 Card PRA interface card runs on software acquired from
the system. After the card has been installed it will automatically load the
required software.

●

The maximum range is 300 m.

●

The short-circuit-proof feed voltage is –42 V/7 W. The feed is suitable to
supply an NTPM with power.

Pin assignment

The following table shows the pin assignment for the RJ45 connector of the
interface (labelled “S2M”; see the illustration

Forum 550 Card PRA: Front

The following table shows the pin assignment for the RJ45 connector of the
power feed cable (labelled “–42 V”; see the illustration

Forum 550 Card PRA:

Pin number

Assignment

1

IN a

2

IN b

3

Not used

4

OUT a

5

OUT b

6

Not used

7

Not used

8

Not used

Pin number

Assignment

1

Not used

2

Not used

3

–42 V

4

0 V

«
...
123
124
125
126
127
...
»

Содержание Forum 500 Series





























































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Forum 500 Series

Бренд: Panasonic Страницы: 2

RXD15 - RADIO CASSETTE W/CD

Бренд: Panasonic Страницы: 8

SyncMaster VC240

Бренд: Samsung Страницы: 39

Бренд: Samsung Страницы: 91

Бренд: Samsung Страницы: 80

Бренд: Xantrex Страницы: 4

Бренд: Xantrex Страницы: 20

Бренд: V2 Страницы: 48

Бренд: Dolby Laboratories Страницы: 31

Бренд: Harman Страницы: 20

PowerVIEW HD-30

Бренд: VADDIO Страницы: 24

WEB’LOG RESIDENTIAL

Бренд: Meteo Control Страницы: 4

WALLACE & TIERNAN SFC SC

Бренд: Evoqua Страницы: 82

Бренд: Clatronic Страницы: 78

Бренд: Oase Страницы: 87

Бренд: Skov Страницы: 28

Бренд: Planet Страницы: 48

Бренд: Panasonic Страницы: 100

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды