manualshive.com logo in svg

Proximus Forum 500 Series, Руководство по монтажу и пусконаладке

Поделиться
Скачать
Proximus Forum 500 Series Скачать руководство пользователя страница 308

Remote Switching

306

Application Interfaces

Example:

 A sensor “A” sends the “Light on” command to the group 

address 1/0/1. All actors with group address 1/0/1 are switched on.

Sensors and actors can have several group addresses. Every action can be 
sent to a list of up to 10 group addresses. The group addresses used by the 
field bus are programmed via the ETS tool. 

Configuration

You can configure the 

Remote switching

 function in the 

Configurator

, menu 

Telephony > Extended > Remote switching

.

Status page 

Remote switching

 

The status page shows the following information:

●

current configuration of the remote switching IP router;

●

current status of the connection between the Forum 5004/5008/5012 
communications system and the remote switching IP router: 

– A tick indicates that the connection is established.

– A cross indicates that the connection could not be established yet.

●

table overview of configured actions and parameters. 

Содержание Forum 500 Series





























































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды