Proximus Forum 500 Series Скачать руководство пользователя страница 133 | Manualshive

Страница: 133 / 348

background image

Forum Gateway 560 Modules

131

The Forum 550 Media Gateway Card interface card can be installed in any of a
Forum Gateway 560 slots (1 to 12, see also the chapter

Technical data

●

The Forum Gateway 560 is connected to the LAN via the Ethernet port
(10/100 MBit/s).

●

The interface card supports: G.711 (A-Law) and G.729 codecs, silence
detection, echo suppression and DTMF tone detection.

●

The interface card can also be operated on a Forum Gateway 560 which is
connected via a PCM-V line.

●

The interface card acquires its software from the system. After the card has
been installed it will automatically load the required software.

●

No settings need to be made on the interface card.

Pin assignment

The ethernet port’s pin assignment is designed for a direct connection, via a
RJ45 patch cable, to an ethernet Switch. You will need a cross-link cable
(“Cross-over Cable”) for connection to a PC.

Indicators

There are four LEDs on the front of the Forum 550 Media Gateway Card
interface card.

Forum 550 Media Gateway Card: LEDs

ETH

MG+ETH1-1

1
2

3
4

«
...
131
132
133
134
135
...
»

Содержание Forum 500 Series





























































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Forum 500 Series

Бренд: iDance Страницы: 25

REMOTE ACCESS SYSTEM 1500

Бренд: 3Com Страницы: 62

Бренд: WAGNER Страницы: 128

Бренд: ENTRYPASS Страницы: 27

Бренд: Polyaire Страницы: 20

Бренд: ZheJiang Libiao Robotics Страницы: 10

Бренд: Konftel Страницы: 8

SAM GENERATION 2

Бренд: HALE Страницы: 12

Бренд: Sena Страницы: 26

Бренд: FONESTAR Страницы: 24

Бренд: Jensen Страницы: 15

Бренд: Qtx Страницы: 5

Бренд: Laser Страницы: 1

MERLIN LEGEND Release 2.0 Analog Multiline Telephone

Бренд: AT&T Страницы: 794

Бренд: Hyundai Страницы: 88

ARMT.665230.202-01

Бренд: ARMTEL Страницы: 36

Бренд: Hitachi Страницы: 14

Бренд: Hitachi Страницы: 4

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды