Proximus Forum 500 Series Скачать руководство пользователя страница 55 | Manualshive

Страница: 55 / 348

background image

Interface Assignment, Cable Length

Installation

53

Please note:

Please observe the following information and recommenda-
tions when connecting analogue devices. Devices which do not
comply with these technical prerequisites may damage the
Forum 5004/5008/5012!

Analogue telephones

The Forum 5004/5008/5012 communications system only supports DTMF
devices.

Music on Hold

TheThe Forum 5004/5008/5012 communications system provides a preset
internal MoH, for which you can also use your own melody. that you can
replace in the

Configurator

of the Web console, in the

System: Components

menu. Please see the online help for further details.

Voice mail

If you are using an external mail system, it must be able to handle the number
of digits used for internal telephone numbers, e. g. five digits, if you have set
up the system to use 5-digit internal numbers.

The external voice mail system can be operated using internal a/b ports. The
voice mail system can send messages to system terminals using code
procedures:

* 6 8 Z

[Terminal]

0

: There is a message for this subscriber

* 6 8 Z

[Terminal]: There is no message (without trailing “0”).

Intercom system (for a/b)

The “Doorphone” intercom system can be connected to any a/b port. The
“Doorphone” module also provides the actor for the door opener contact.

Please observe the following points when connecting the door intercom
system:

●

The “Doorphone” module should be set to its factory setting.

In the

Telephony

:

Ports

:

a/b

:

Change

menu in the Configurator, select

Doorstation 2-wire

as the

Type

. The

Actor

setting is for selecting

whether you wish to use the “Doorphone” relay (“Actor internal”) or one of
the two internal actors of the hardware unit (“Actor 1” or “Actor 2”). You
can also configure the same actor for different intercom systems.

Code

is

where you also configure the desired code procedure for the intercom
system. Select the “*102, *112” entry, e.g. for calling the intercom system
via the

* 1 0 2

code procedure and for opening the door via the

«
...
53
54
55
56
57
...
»

Содержание Forum 500 Series





























































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Forum 500 Series

ElectraElite IPK

Бренд: NEC Страницы: 20

FUSION Apollo MS-WB670

Бренд: Garmin Страницы: 44

Бренд: TCS Страницы: 16

Бренд: Teac Страницы: 3

Бренд: Brähler Systems Страницы: 25

Бренд: IDEATEC Страницы: 32

SPACOMMAND CP3800 Series

Бренд: Pentair Страницы: 36

Бренд: Magnavox Страницы: 25

Бренд: Steren Страницы: 12

Бренд: Foxtech Страницы: 63

Бренд: JVC Страницы: 19

Бренд: JVC Страницы: 36

Бренд: JVC Страницы: 2

Бренд: AudioBahn Страницы: 13

Бренд: Sony Страницы: 10

Бренд: Sony Страницы: 74

Бренд: Sony Страницы: 78

Бренд: Sony Страницы: 200

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды