Proximus Forum 500 Series Скачать руководство пользователя страница 108

Страница: 108 / 348

Interfaces and Connectible Terminals

106

Termination

Each interface card has 16 DIP switches (S1 to S16, two per S

interface). The

DIP switches activate the required terminating resistors for the S

buses

(100 ohms per S

bus). In the default setting, all terminating resistors are

activated (Default: on).

Forum 550 Card 8 S0/T0: Location of DIP switches S1 to S16

Note:

The following configuration information applies to external as
well as internal S

interfaces.

Bus configuration: Forum Gateway 560 at the end of an S

bus

If the Forum Gateway 560 is connected at the end of an S

bus, the

terminating resistors of the relevant S

interface cards must be activated.

In a typical configuration, the Forum Gateway 560 will be connected to the
network termination for basic access (NTBA) with an externally switched S

port; therefore, all terminating resistors of the interface card are activated in
the default setting.

Send -

Not used

Pin number

Assignment

Содержание Forum 500 Series





























































































































































































































































































































































Результаты поиска

Содержание Forum 500 Series

Отзывы:

Похожие инструкции для Forum 500 Series

Бренды по названию

Популярные бренды

Proximus Forum 500 Series, Руководство по монтажу и пусконаладке

Результаты поиска

Содержание Forum 500 Series

Отзывы:

Похожие инструкции для Forum 500 Series

Бренды по названию

Популярные бренды