KW DAVID 613, Руководство по эксплуатации, Страница: 158 / 264

KW Aufzugstechnik GmbH OPERATING MANUAL DAVID-613
DAVID-D613-V125-E 13.04.2021 Page - 158 -
B619 ATTENDANT MODE
In the menu B619 you can acivate the Attendant Mode (C&A) and the activation-time. With a pulse at
the input-function E463 (Attendant Mode ON) the attendant mode will be activated.
With a pulse at the input-function E464 (Attendant Mode OFF) the attendant mode will be switched off
and all car calls will be erased. Another way to switch off the attendant mode is the ending time in menu
B619 (time parameter).
If the attendant mode is active, the output function A371 is high and the photocells are passive.
All floor blocking is switched off. All calls are indicated. They are saved but not in work.
When the input-function E465 ( Attendant Mode UP ) or E466 ( Attendant Mode DOWN ) is going high,
then the door is closing, until the push-button of the input-function is activated.
The elevator begins his travel in this direction, if there is a call. When the push-button is switch off,
before the door is closed, then the door opens again.
With a pulse at the input-function E467 ( Attendant Mode Landing calls OFF ), all landing calls will be
erased and the landing control is switched off. The indicator “OUT OF ORDER” is activated.
With a second pulse at the input-function E467 the landing-control is switched on. Until the landing-
control is not active, there is a back-message to the output-function A372 ( Attendant Mode Landing
calls OFF ).
B620 DEADMAN MODE
In general you must acivate the Deadman Mode in the menu
A2.2 controller type
with the parameter
„ 1K-Deadman “.
In the menu B620 Deadman Mode you can switch on the Deadman Mode on two ways, namely there
is used a „One-Hand-Operation“ or a „Two-Hand-Operation“.
If the parameter input „Switch on over car calls“ is choosen, you have the „One-Hand-Operation-
Mode“, because the car-priority-key is active and the car-call push-button must switch on, until the
destination floor is arrived. If the car call is switched off during the travel, the elevator stops and the call
is erased.
If the parameter input „Switch on over E327“ is choosen, you have the „Two-Hand-Operation-Mode“
activated. If you want to begin a travel, you must switch on the key for car –priority.
After that you can push a car call and in the same time, the input-channel E327 ( Ready for travel ) must
be switched on. The indicators of the car-call are switched off (no output-function).
If the input-function E327 is switched off during the travel, the elevator stops and the call is erased.
If the car-priority active at the end of the travel, it will be determined with a time delay of 10 seconds.
When the hand-shaft-door will be opened, then the time-delay will be soon stopped. You can avoid with
this method that the elevator will be started with a landing call.
In the menu B620 Photocell monitoring you can switch on or off the work with the photocells. If the
parameter is active, there is only a reaction, if the car priority is active ( travel with car calls).
If the light of the photocell is broken, the travel will be stopped, or the travel will not be started The in-
put-functions are „E345 Photocell Door 1“ and „E349 Photocell Door 2“. The input-functions are at
the input-channels FE0 and FE4 of the FKR.
In the menu on B620 Landing Calls over car call, the external calls via the car call functions are han-
dled -> platform lifts with landing call-dead man.
In Menu mode, the B620 deadman fireplace special function is activated for fire service lifts. -> Land-
ing call-dead man with temporary activation, depending on the position of the cabin.