manualshive.com logo in svg

horiba TPNA-500, Инструкция по эксплуатации

Поделиться
Скачать
horiba TPNA-500 Скачать руководство пользователя страница 101

 Function

85

SYNCHRONOUS IDLE

Specifies the synchronous signal.

Tip

If you wish to output a signal before the sequence starts, specify a negative value. For example, when

10 sec is specified, the signal is output 10 seconds before the sequence starts.

Operation procedure

1.

Press [EXT. POINT OUTPUT SET] in the OUTPUT SET screen.

2.

Press [SYNCHRONOUS IDLE] in the EXT. PO SET screen.

The SYNCHRONOUS IDLE screen will be displayed.

3.

Specify the synchronous signal.

Operation mode

Setting 

range

Default 

value

Description

SYNCHRONOUS 
IDLE 1

ON

-3,600 sec
to 3600 sec

0 sec

The time period for which the signal is turned ON in 
synchronization with the measurement sequence.

OFF

3600 sec

The time period for which the signal is turned OFF in 
synchronization with the measurement sequence.

SYNCHRONOUS 
IDLE 2

ON

-3600 sec
to 3600 sec

0 sec

The time period for which the signal is turned ON in 
synchronization with the measurement sequence.

OFF

3600 sec

The time period for which the signal is turned OFF in 
synchronization with the measurement sequence.

Main              

　

 MENU              

　

 SETTING             

　

 OUTPUT SET

[MENU]

[OUTPUT SET] 

 [SETTING]

Refer to “ To display the [MENU] item screen” (page 62).

[EXT. POINT 

OUTPUT SET

EXT. PO SET

[SYNCHRONOUS IDLE]

OUTPUT SET]

[SYNCHRONOUS 

[SYNCHRONOUS 

SYNCHRONOUS IDLE

SYNCHRONOUS IDLE 1

SYNCHRONOUS IDLE 2

ON/OFF

ON/OFF

<Input a value>

<Input a value>

IDLE 1]

IDLE 2]

[      ]

[      ]

Содержание TPNA-500






































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды