manualshive.com logo in svg

Toyota 1996 LAND CRUISER, User Manual

Get your hands on the user manual for the powerful Toyota 1996 LAND CRUISER for free download. This manual is essential for understanding the ins and outs of this iconic vehicle. Download it now from manualshive.com and take your driving experience to the next level.

Share
Download
background image

TR0BG

−

01

TF0967

SST

TF0943

SST

TF0939

TF0945

SST

−

TRANSFER

FRONT EXTENSION HOUSING

TR

−

27

1996 LAND CRUISER   (RM451U)

REASSEMBLY

HINT:
Coat all of the sliding and rotating surfaces with gear oil before
assembly.

1.

INSTALL DUST DEFLECTOR

(a)

Using SST and a press, install a new dust deflector to the
front extension housing.
SST

09223

−

15020, 09950

−

70010 (09951

−

07150)

(b)

Using SST and a press, install a new dust deflector to the
front output shaft.
SST

09316

−

20011, 09316

−

60011 (09316

−

00011)

2.

INSTALL BALL BEARING

(a)

Using SST and a press, install the ball bearing to the front
extension housing.
SST

09316

−

60011 (09316

−

00011, 09316

−

00031)

(b)

Select a snap ring that will allow minimum axial play.

Mark

Thickness   mm (in.)

A

1.7 (0.0669)

B

1.8 (0.0709)

(c)

Using a screwdriver, install a new snap ring.

3.

INSTALL OIL SEAL

Using SST and a hammer, drive in a new oil seal to the front ex-
tension housing.

SST

09316

−

60011 (09316

−

00011, 09316

−

00061)

Brought to you by BirfMark

Brought to you by BirfMark 
 Version 1.00 - 12/21/2010

Summary of Contents for 1996 LAND CRUISER






































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for 1996 LAND CRUISER

Ford 2008 Mustang Quick Reference Manual preview
2008 Mustang
Brand: Ford Pages: 2
Mazda 2 2016 Owner'S Manual preview
2 2016
Brand: Mazda Pages: 720
iRacing Porsche 911 GT3 R User Manual preview
Porsche 911 GT3 R
Brand: iRacing Pages: 25
Honda Pilot 2019 Owner'S Manual preview
Pilot 2019
Brand: Honda Pages: 85
Mazda 2006 RX-8 Service Highlights preview
2006 RX-8
Brand: Mazda Pages: 122
Elinchrom ELB 1200 User Manual preview
ELB 1200
Brand: Elinchrom Pages: 101
Thule 953000 Instructions Manual preview
953000
Brand: Thule Pages: 8
Aston Martin V8 Vantage Workshop Manual preview
V8 Vantage
Brand: Aston Martin Pages: 415
Brodit ProClip 833995 Manual preview
ProClip 833995
Brand: Brodit Pages: 2
Federal Signal Corporation HighLighter Installation And Programming preview
HighLighter
Brand: Federal Signal Corporation Pages: 20
Federal Signal Corporation Cuda TriOptic 351014F Series Instruction Sheet preview
Cuda TriOptic 351014F Series
Brand: Federal Signal Corporation Pages: 4
Kia Magentis 2002 Owner'S Manual preview
Magentis 2002
Brand: Kia Pages: 216
Rajant 23-100068-001 Quick Start Manual preview
23-100068-001
Brand: Rajant Pages: 11
Prime Design VRI3-FT31B Assembly Manual preview
VRI3-FT31B
Brand: Prime Design Pages: 16
Kia K900 2017 Features & Functions Manual preview
K900 2017
Brand: Kia Pages: 62
Kia Forte 2020 Features & Functions Manual preview
Forte 2020
Brand: Kia Pages: 50
Kia EV6 2022 Manual preview
EV6 2022
Brand: Kia Pages: 70
Kia Carnival 2009 General Information Manual preview
Carnival 2009
Brand: Kia Pages: 49

Brands by name

Popular brands

Load more brands