Toyota 1996 LAND CRUISER User Manual Download Page 254

Page: 254 / 1381

BO37S

−

BODY

REAR DOOR

−

1996 LAND CRUISER (RM451U)

DISASSEMBLY

HINT:
Tape a screwdriver tip before using to pry parts.

REMOVE DOOR INSIDE HANDLE BEZEL

REMOVE DOOR SPEAKER COVER

REMOVE ASH TRAY

REMOVE ARMREST BASE UPPER

REMOVE ARMREST

REMOVE DOOR TRIM

(a)

Remove the courtesy light.

(b)

Remove the 3 screws from the door trim.

(c)

Using a screwdriver, remove the clips and remove the trim
by pulling all of the trim up.

(d)

Remove the inner weatherstrip from the door trim.

(e)

Remove the 11 screws and the armrest base from the
door trim.

REMOVE DOOR BELT MOULDING

Pry out the clip from the edge of the panel, and remove the
moulding.

REMOVE DOOR WEATHERSTRIP

NOTICE:
Do not pull strongly on the weatherstrip as it may tear.
9.

REMOVE DOOR INSIDE HANDLE

10. REMOVE SERVICE HOLE COVER

Brought to you by BirfMark

Brought to you by BirfMark
Version 1.00 - 12/21/2010

Summary of Contents for 1996 LAND CRUISER






































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for 1996 LAND CRUISER

Reviews:

Related manuals for 1996 LAND CRUISER

Brands by name

Popular brands

Toyota 1996 LAND CRUISER, User Manual

Search results

Summary of Contents for 1996 LAND CRUISER

Reviews:

Related manuals for 1996 LAND CRUISER

Brands by name

Popular brands