manualshive.com logo in svg

Toyota 1996 LAND CRUISER, User Manual, Page: 342 / 1381

Share
Download
Toyota 1996 LAND CRUISER User Manual Download Page 342

BR1CI-01

R13497

R13591

BR-10

-

BRAKE

BRAKE MASTER CYLINDER

1996 LAND CRUISER  (RM451U)

REMOVAL

1.

DISCONNECT LEVEL WARNING SWITCH CONNEC-
TOR

2.

TAKE OUT FLUID WITH SYRINGE

NOTICE:
Do not let brake fluid remain on a painted surface. Wash it
off immediately.

3.

DISCONNECT BRAKE LINES

Using SST, disconnect the 4 brake lines from the master cylin-
der and 3-way.

SST

09023-00100

Torque: 15 N·m (155 kgf·cm, 11 ft·lbf)

4.

REMOVE MASTER CYLINDER

(a)

Remove the 4 nuts.
Torque: 13 N·m (130 kgf·cm, 9 ft·lbf)

(b)

Remove  the  3-way, check valve bracket, wire harness
clamp and bracket.

(c)

Pull out the master cylinder and gasket.

Brought to you by BirfMark

Brought to you by BirfMark 
 Version 1.00 - 12/21/2010

Summary of Contents for 1996 LAND CRUISER






































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments