manualshive.com logo in svg

Toyota 1996 LAND CRUISER, User Manual, Page: 147 / 1381

Share
Download
Toyota 1996 LAND CRUISER User Manual Download Page 147

BE

−

4

−

BODY ELECTRICAL

BODY ELECTRICAL SYSTEM

1996 LAND CRUISER   (RM451U)

Back

−

Up light remains on.

1. Park/Neutral Position Switch (A/T)
2. Wire Harness

−
−

Only one light does not light up.

1. Bulb
2. Wire Harness

−
−

STOP LIGHT SYSTEM

Symptom

Suspect Area

See page

Stop light does not light up.

1. STOP Fuse (I/P F/B)
2. Stop Light Switch
3. Bulb
4. Wire Harness

−

BE

−

25

−
−

Stop light remains always on.

1. Stop Light Switch
2. Wire Harness

BE

−

25

−

Only one light does not light up.

1. Wire Harness
2. Bulb

−
−

WIPER AND WASHER SYSTEM

Symptom

Suspect Area

See page

Wipers do not operate or return to off position.

1. WIPER Fuse (I/P F/B)
2. Wiper Switch
3. Wiper Motor
4. Wiper Relay
5. Wire Harness

BE

−

27

BE

−

27

BE

−

27

BE

−

27

−

Wipers do not operate in MIST.

1. Wiper Switch
2. Wiper Motor
3. Wiper Relay
4. Wire Harness

BE

−

27

BE

−

27

BE

−

27

−

Wipers do not operate in INT.

1. Wiper Switch
2. Wiper Motor
3. Wiper Relay
4. Wire Harness

BE

−

27

BE

−

27

BE

−

27

−

Washer does not operate.

1. Washer Hose or Nozzle Clogged
2. Washer Switch
3. Washer Motor
4. Wire Harness

−

BE

−

27

BE

−

27

−

METER, GAUGES AND ILLUMINATION:
COMBINATION METER

Symptom

Suspect Area

See page

Tachometer, speedometer, engine coolant temperature gauge and
fuel gauge do not operate.

1. GAUGE Fuse (I/P F/B)
2. Meter Circuit
3. Wire Harness

−

BE

−

32

−

Speedometer does not operate.

1. No.1 Vehicle Speed Sensor
2. Speedometer Driven Gear and Drive Gear
3. Meter Circuit
4. Wire Harness

BE

−

34

−

BE

−

32

−

Tachometer does not operate.

1. Meter Circuit
2. Igniter
3. Wire Harness

BE

−

32

−
−

Tachometer does not operate.

1. Meter Circuit
2. Igniter
3. Wire Harness

BE

−

32

−
−

Voltmeter does not operate.

1. Voltmeter Receiver Gauge
2. Wire Harness

AT

−

6

−

Brought to you by BirfMark

Brought to you by BirfMark 
 Version 1.00 - 12/21/2010

Summary of Contents for 1996 LAND CRUISER






































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments