Toyota 1996 LAND CRUISER User Manual Download Page 181

Page: 181 / 1381

BE4917

Test LED

Battery

BE1217

Warning Light

Ignit ion

Switch

Battery

N01212

−

BODY ELECTRICAL

COMBINATION METER

1996 LAND CRUISER (RM451U)

(c)

Ground terminal on the wire harness side through a 3.4
W test bulb.

(d)

Turn the ignition switch ON, and check that the bulb lights
up and that the receiver gauge needle moves to the high
side.

If operation is not as specified, measure the receiver gauge re-
sistance.

14. INSPECT OIL PRESSURE RECEIVER GAUGE RESIS-

TANCE

Measure the receiver gauge resistance between terminals.

Resistance:
40

−

If resistance value is not as specified, replace the receiver
gauge.

15. INSPECT OIL PRESSURE SENDER GAUGE OPERA-

TION

(a)

Disconnect the connector from the sender gauge.

(b)

Apply battery positive voltage to the sender gauge termi-
nal through a test LED.

(c)

Check that the bulb does not light when the engine is
stopped.

(d)

Check that the LED flashes when the engine is running.
The number of flashed should vary with engine speed.

If operation is not as specified, replace the sender gauge.

16. INSPECT BRAKE WARNING LIGHT

(a)

Disconnect the connectors from the level warning switch
and parking brake switch.

(b)

Connect terminals on the wire harness side connector of
the level warning switch connector.

(c)

Turn the ignition switch ON, and check that the warning
light lights up.

17. INSPECT PARKING BRAKE SWITCH

(a)

Check that there is continuity between terminal and the
switch set nut with switch pin released (parking brake le-
ver pulled up).

(b)

Check that there is no continuity between terminal and
the switch set nut with switch pin pushed in. (parking
brake lever released)

If operation is not as specified, replace the switch.

Brought to you by BirfMark

Brought to you by BirfMark
Version 1.00 - 12/21/2010

Summary of Contents for 1996 LAND CRUISER






































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for 1996 LAND CRUISER

Reviews:

Related manuals for 1996 LAND CRUISER

Brands by name

Popular brands

Toyota 1996 LAND CRUISER, User Manual

Search results

Summary of Contents for 1996 LAND CRUISER

Reviews:

Related manuals for 1996 LAND CRUISER

Brands by name

Popular brands