Toyota 1996 LAND CRUISER User Manual Download Page 878

Page: 878 / 1381

−

ENGINE MECHANICAL

CYLINDER BLOCK

1996 LAND CRUISER (RM451U)

INSPECT BEARING OF OIL PUMP DRIVE SHAFT
GEAR

Check the bearing for pitting and scratches.
If the bearing is damaged, replace the cylinder block.

CLEAN PISTON

(a)

Using a gasket scraper, remove the carbon from the pis-
ton top.

(b)

Using a groove cleaning tool or broken ring, clean the pis-
ton ring grooves.

(c)

Using solvent and a brush, thoroughly clean the piston.

NOTICE:
Do not use a wire brush.

INSPECT PISTON AND CONNECTING ROD

(a)

Inspect the piston oil clearance.

HINT:
There are 3 sizes of the standard piston diameter, marked ”1”,
”2” and ”3”. The mark is stamped on the piston top.

Brought to you by BirfMark

Brought to you by BirfMark
Version 1.00 - 12/21/2010

Summary of Contents for 1996 LAND CRUISER






































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for 1996 LAND CRUISER

Reviews:

Toyota 1996 LAND CRUISER, User Manual, Page: 878 / 1381

Search results

Summary of Contents for 1996 LAND CRUISER

Reviews: