manualshive.com logo in svg

Toyota 1996 LAND CRUISER, User Manual, Page: 290 / 1381

Share
Download
Toyota 1996 LAND CRUISER User Manual Download Page 290

BO38T

−

01

−

BODY

QUARTER WINDOW GLASS

BO

−

51

1996 LAND CRUISER   (RM451U)

REMOVAL

1.

w/ No. 2 rear seat:
NO. 2 REAR SEAT

2.

REMOVE BACK DOOR SCUFF PLATE

3.

REMOVE QUARTER TRIM

4.

REMOVE REAR SEAT SIDE GARNISH

5.

REMOVE REAR DOOR SCUFF PLATE

6.

REMOVE QUARTER PILLAR GARNISH

7.

REMOVE REAR PILLAR GARNISH

8.

REMOVE ASSIST GRIPS

9.

LOOSEN ROOF HEADLINING

10. REMOVE VENT LOUVER AND QUARTER BELT

MOULDING

(a)

Remove the nut from the vent louver.

(b)

Insert a screwdriver between the retainers and body to
pry it loose.

HINT:
Tape the screwdriver tip before use.
(c)

Pull out the vent louver.

(d)

Pull out the clips from the edge of the panel, and remove
the moulding.

Brought to you by BirfMark

Brought to you by BirfMark 
 Version 1.00 - 12/21/2010

Summary of Contents for 1996 LAND CRUISER






































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments