Toyota 1996 LAND CRUISER User Manual Download Page 854

Page: 854 / 1381

−

ENGINE MECHANICAL

ENGINE UNIT

1996 LAND CRUISER (RM451U)

13. DISCONNECT ENGINE WIRE AND HEATER VALVE

FROM COWL PANEL

(a)

Remove the 2 bolts and disconnect the engine wire and
ground strap.

(b)

Remove the 2 bolts and disconnect the heater valve.

14. DISCONNECT BRAKE BOOSTER VACUUM HOSE
15. DISCONNECT EVAP HOSE
16. DISCONNECT FUEL HOSES

(a)

Disconnect the fuel return hose.

(b)

Remove the union bolt and 2 gaskets, and disconnect the
fuel inlet hose from the fuel filter.

17. DISCONNECT WIRES AND CONNECTORS

(a)

Disconnect the 2 heated oxygen sensor connectors.

(b)

Disconnect the DLC1 clamp.

(c)

Disconnect the 2 oil pressure gauge connectors.

(d)

Disconnect the generator wire and connector.

(e)

Disconnect the connector on the intake manifold from the
fender apron.

(f)

Disconnect the high

−

tension cord from the ignition coil.

(g)

Disconnect the ground strap from the No. 1 engine hang-
er.

(h)

Disconnect the ground strap from the air intake chamber.

(i)

Disconnect the starter wire.

(j)

Disconnect the ground cable from the cylinder block.

18. DISCONNECT A/C COMPRESSOR AND BRACKET

(a)

Loosen the idler pulley nut and adjusting bolt, and remove
the drive belt.

(b)

Remove the 4 mounting bolts, and disconnect the com-
pressor from the bracket.

HINT:
Put aside the compressor, and suspend it.
(c)

Remove the 5 bolts and A/C compressor bracket.

19. REMOVE RADIATOR PIPE

(a)

Remove the 2 nuts holding the radiator pipe to the No. 1
oil pan.

(b)

Disconnect the No. 2 radiator hose from the water inlet
and remove the radiator pipe.

Brought to you by BirfMark

Brought to you by BirfMark
Version 1.00 - 12/21/2010

Summary of Contents for 1996 LAND CRUISER






































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for 1996 LAND CRUISER

Reviews:

Related manuals for 1996 LAND CRUISER

Brands by name

Popular brands

Toyota 1996 LAND CRUISER, User Manual

Search results

Summary of Contents for 1996 LAND CRUISER

Reviews:

Related manuals for 1996 LAND CRUISER

Brands by name

Popular brands