manualshive.com logo in svg

Toyota 1996 LAND CRUISER, User Manual

Get your hands on the user manual for the powerful Toyota 1996 LAND CRUISER for free download. This manual is essential for understanding the ins and outs of this iconic vehicle. Download it now from manualshive.com and take your driving experience to the next level.

Share
Download
background image

SA1U8

−

02

R03031

R13503

R07928

−

SUSPENSION AND AXLE

TIRE AND WHEEL

SA

−

3

860

Author:

Date:

1996 LAND CRUISER   (RM451U)

TIRE AND WHEEL

INSPECTION

1.

INSPECT TIRE

(a)

Check the tires for wear and for the proper inflation pres-
sure.

Cold tire inflation pressure: See page 

SS

−

30

(b)

Check the tire runout.

Tire runout: 3.0 mm (0.118 in.) or less

2.

ROTATE TIRES

HINT:
See the illustration for where to rotate each tire.

3.

INSPECT WHEEL BALANCE

(a)

Check and adjust the Off

−

the

−

car balance.

(b)

If necessary, check and adjust the On

−

the

−

car balance.

Unbalance after adjustment: 13.0 g (0.029 lb) or less

4.

CHECK WHEEL BEARING LOOSENESS

Check the no backlash in the bearing shaft direction.

5.

CHECK FRONT SUSPENSION FOR LOOSENESS

6.

CHECK STEERING LINKAGE FOR LOOSENESS

7.

CHECK BALL JOINT FOR LOOSENESS

8.

CHECK SHOCK ABSORBER WORKS PROPERLY

S

Check for oil leaks

S

Check mounting bushings for wear

S

Bounce front and rear of the vehicle

Brought to you by BirfMark

Brought to you by BirfMark 
 Version 1.00 - 12/21/2010

Summary of Contents for 1996 LAND CRUISER






































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for 1996 LAND CRUISER

AAMP of America iSimple Operation Manual preview
iSimple
Brand: AAMP of America Pages: 6
B-Speech B-Speech Prim Manual preview
B-Speech Prim
Brand: B-Speech Pages: 18
Cadillac 2011 CTS COUPE Personalization Manual preview
2011 CTS COUPE
Brand: Cadillac Pages: 20
Cadillac 2011 CTS COUPE Specifications preview
2011 CTS COUPE
Brand: Cadillac Pages: 2
Cadillac 2009 CTS Owner'S Manual preview
2009 CTS
Brand: Cadillac Pages: 494
Cadillac 2008 Escalade Owner'S Manual preview
2008 Escalade
Brand: Cadillac Pages: 500
Cadillac 2006 Escalade Warranty And Owner Assistance Information preview
2006 Escalade
Brand: Cadillac Pages: 40
Cadillac 2004 DeVille Owner'S Manual preview
2004 DeVille
Brand: Cadillac Pages: 432
Cadillac 1997 Catera Owner'S Manual preview
1997 Catera
Brand: Cadillac Pages: 338
Cadillac 2009 STS Get To Know preview
2009 STS
Brand: Cadillac Pages: 20
Cadillac 2005 STS Owner'S Manual preview
2005 STS
Brand: Cadillac Pages: 438
Phonocar VM350 Mounting Instructions preview
VM350
Brand: Phonocar Pages: 2
Toyota 4Runner 2019 Quick Reference Manual preview
4Runner 2019
Brand: Toyota Pages: 52
HAUL MASTER 41782 Assembly And Operating Instructions Manual preview
41782
Brand: HAUL MASTER Pages: 8
Chevrolet 2014 TRAX Owner'S Manual preview
2014 TRAX
Brand: Chevrolet Pages: 412
Oldsmobile 2000 Oldsmobile Intrigue Owner'S Manual preview
2000 Oldsmobile Intrigue
Brand: Oldsmobile Pages: 348
Safe Fleet PRIME DESIGN VRR3-FT21G-ST Manual preview
PRIME DESIGN VRR3-FT21G-ST
Brand: Safe Fleet Pages: 12
RAM 2013 2500 Big Horn Information preview
2013 2500 Big Horn
Brand: RAM Pages: 12

Brands by name

Popular brands

Load more brands