Toyota 1996 LAND CRUISER User Manual Download Page 529 | Manualshive

Page: 529 / 1381

background image

−

DIAGNOSTICS

ENGINE

DI

−

93

1996 LAND CRUISER (RM451U)

DTC

P0510

Closed Throttle Position Switch Malfunction

CIRCUIT DESCRIPTION

Refer to DTC P0120 (Throttle/Pedal Position Sensor/Switch ”A” Circuit Malfunction) on page

DI

−

35

.

DTC No.

DTC Detecting Condition

Trouble Area

P0510

The closed throttle position switch does not turn ON or OFF
even once when the vehicle is driven
(2 trip detection logic)

S

Open or short in closed throttle position switch circuit

S

Closed throttle position switch

S

ECM

HINT:
After confirming DTC P0510 use the TOYOTA hand

−

held tester to confirm the closed throttle position switch

signal from ”CURRENT DATA”.

Throttle Valve

Closed Throttle Position Switch Signal

Malfunction

Fully closed

OFF

Open circuit

Fully open

ON

Short circuit

WIRING DIAGRAM

Refer to DTC P0120 (Throttle/Pedal Position Sensor/Switch ”A” Circuit Malfunction) on page

DI

−

35

for WIR-

ING DIAGRAM.

INSPECTION PROCEDURE

HINT:
If DTCs P0110 (Intake Air Temp. Circuit Malfunction), P0115 (Engine Coolant Temp. Circuit Malfunction),
P0120 (Throttle/Pedal Position Sensor/Switch ”A” Circuit Malfunction) are output simultaneously, E2 (Sen-
sor Ground) may be open.

TOYOTA hand

−

held tester

1

Connect the TOYOTA hand

−

held tester and read CTP switch signal.

PREPARATION:

(a)

Remove the fuse cover on the instrument panel.

(b)

Connect OBD II scan tool or TOYOTA hand

−

held tester to the DLC3.

(c)

Turn ignition switch ON and OBD II scan tool or TOYOTA hand

−

held tester main switch ON.

CHECK:

Read CTP switch signal on TOYOTA hand

−

held tester.

RESULT:

Throttle Valve

Closed Throttle Position Switch Signal

Malfunction

Fully closed

OFF

Open circuit: Go to step 2

Fully open

ON

Short circuit: Go to step 4

DI5PP

−

02

Brought to you by BirfMark

Brought to you by BirfMark
Version 1.00 - 12/21/2010

«
...
527
528
529
530
531
...
»

Summary of Contents for 1996 LAND CRUISER






































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for 1996 LAND CRUISER

Brand: Dynojet Pages: 68

Brand: Kuda-Phonebase Pages: 3

Brand: Harbor Freight Tools Pages: 12

Brand: Honda Pages: 3

1966 Spider 105

Brand: Alfa Romeo Pages: 46

Brand: Pontiac Pages: 486

Brand: Toyota Pages: 779

Brand: Whispbar Pages: 77

Brand: Federal Signal Corporation Pages: 20

Brand: EUFAB Pages: 18

Brand: travall Pages: 4

Brand: Quadratec Pages: 8

Brand: UCANDAS Pages: 4

Brand: BMW Pages: 242

Brand: v.link Pages: 20

Brand: Yutrax Pages: 8

Brand: Metra Electronics Pages: 2

Brand: Myenergi Pages: 51

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands