Toyota 1996 LAND CRUISER User Manual Download Page 915

Page: 915 / 1381

P22576

−

LUBRICATION

OIL PUMP

−

1996 LAND CRUISER (RM451U)

(b)

Remove the No.1 oil pan by prying the portions (A) be-
tween the cylinder block and No.1 oil pan with a screw-
driver.

NOTICE:
Be careful not to damage the contact surfaces of the cylin-
der block and No.1 oil pan.

14. REMOVE OIL PAN BAFFLE PLATE

Remove the bolt, 7 nuts and baffle plate.

15. REMOVE OIL STRAINER

Remove the bolt, 2 nuts, oil strainer and gasket.

16. REMOVE CRANKSHAFT PULLEY (See page

−

)

17. REMOVE DRIVE BELT IDLER PULLEY

Remove the bolt and idler pulley.

18. REMOVE OIL PUMP (TIMING CHAIN COVER) (See

page

−

)

19. REMOVE TIMING CHAIN AND CAMSHAFT TIMING

GEAR

Brought to you by BirfMark

Brought to you by BirfMark
Version 1.00 - 12/21/2010

Summary of Contents for 1996 LAND CRUISER






































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for 1996 LAND CRUISER

Reviews:

Toyota 1996 LAND CRUISER, User Manual, Page: 915 / 1381

Search results

Summary of Contents for 1996 LAND CRUISER

Reviews: