Toyota 1996 LAND CRUISER User Manual Download Page 121

Page: 121 / 1381

Q07268

AT0T0

−

Q07264

Z15453

SST

Z15454

SST

Q07268

−

AUTOMATIC TRANSMISSION

SPEEDOMETER DRIVEN GEAR

−

787

Author:

Date:

1996 LAND CRUISER (RM451U)

SPEEDOMETER DRIVEN GEAR

−

VEHICLE REPAIR

DISCONNECT SPEEDOMETER CABLE AND RE-
MOVE SPEEDOMETER DRIVEN GEAR

(a)

Loosen the serrated collar with pliers. Do not lose the felt
dust protector and washer.

(b)

Disconnect the speedometer cable.

(c)

Remove the bolt and locking plate. Pry out the speedom-
eter driven gear assembly.

(d)

Remove the O

−

ring from the speedometer driven gear

assembly.

(e)

Remove the clip and speedometer driven gear from the
speedometer driven gear sleeve.

REMOVE SPEEDOMETER DRIVEN GEAR OIL SEAL

Using SST, remove the oil seal.

SST

09921

−

00010

REINSTALL SPEEDOMETER DRIVEN GEAR OIL
SEAL

Using SST, install a new oil seal.

SST

09201

−

10000 (09201

−

01080)

Drive in depth: 20 mm (0.79 in.)

REINSTALL SPEEDOMETER DRIVEN GEAR AND
CONNECT SPEEDOMETER CABLE

(a)

Install the clip and speedometer driven gear to the
speedometer driven gear sleeve.

(b)

Install a new O

−

ring to the speedometer driven gear as-

sembly.

(c)

Install the speedometer driven gear.

(d)

Install the locking plate with the bolt.

Torque: 16 N·m (160 kgf·cm, 12 ft·lbf)

(e)

Connect the speedometer cable.

Brought to you by BirfMark

Brought to you by BirfMark
Version 1.00 - 12/21/2010

Summary of Contents for 1996 LAND CRUISER






































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for 1996 LAND CRUISER

Reviews:

Related manuals for 1996 LAND CRUISER

Brands by name

Popular brands

Toyota 1996 LAND CRUISER, User Manual

Search results

Summary of Contents for 1996 LAND CRUISER

Reviews:

Related manuals for 1996 LAND CRUISER

Brands by name

Popular brands