manualshive.com logo in svg

Toyota 1996 LAND CRUISER, User Manual

Get your hands on the user manual for the powerful Toyota 1996 LAND CRUISER for free download. This manual is essential for understanding the ins and outs of this iconic vehicle. Download it now from manualshive.com and take your driving experience to the next level.

Share
Download
background image

BO37R

−

01

BO

−

18

−

BODY

REAR DOOR

1996 LAND CRUISER   (RM451U)

ADJUSTMENT

1.

ADJUST DOOR IN FORWARD/REARWARD AND VER-
TICAL DIRECTIONS

Adjust the door by loosening the body side hinge bolts.

Torque: 24 N·m (240 kgf·cm, 17 ft·lbf)

2.

ADJUST DOOR IN LEFT /RIGHT AND VERTICAL
DIRECTIONS

Adjust the door by loosening the door side hinge bolts.

Torque: 24 N·m (240 kgf·cm, 17 ft·lbf)

3.

ADJUST DOOR LOCK STRIKER

(a)

Check that the door fit and door lock linkages are adjusted
correctly.

(b)

Loosen the striker mounting screws to adjust.

(c)

Using a plastic hammer, tap the striker to adjust it.

Brought to you by BirfMark

Brought to you by BirfMark 
 Version 1.00 - 12/21/2010

Summary of Contents for 1996 LAND CRUISER






































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for 1996 LAND CRUISER

Gardigo MARTEN-FREE CAR Instruction Manual preview
MARTEN-FREE CAR
Brand: Gardigo Pages: 36
Westin 23-3130 Instructions preview
23-3130
Brand: Westin Pages: 3
OCTO SmartDiag2GO GD201-O User Manual preview
SmartDiag2GO GD201-O
Brand: OCTO Pages: 5
Hama 00201510 Operating Instructions Manual preview
00201510
Brand: Hama Pages: 40
Fiat 500 L 2019 User Manual preview
500 L 2019
Brand: Fiat Pages: 172
Honda HondaLink Quick Start Manual preview
HondaLink
Brand: Honda Pages: 6
Mazda 2007 MazdaSpeed6 Specification preview
2007 MazdaSpeed6
Brand: Mazda Pages: 12
U.S. General 95904 Operating Instructions preview
95904
Brand: U.S. General Pages: 4
RAM 2011 DAKOTA User Manual preview
2011 DAKOTA
Brand: RAM Pages: 76
Advantech TREK-550 Manual preview
TREK-550
Brand: Advantech Pages: 59
Waeco 8885100124 Operating Manual preview
8885100124
Brand: Waeco Pages: 172
VBG 56-201901 Mounting Instructions preview
56-201901
Brand: VBG Pages: 16
Honda 08A06-361-210 Installation Instructions preview
08A06-361-210
Brand: Honda Pages: 4
Pro-gard SAFESTOP SS0005 Installation Manual preview
SAFESTOP SS0005
Brand: Pro-gard Pages: 4
Mini COOPER Owner'S Manual preview
COOPER
Brand: Mini Pages: 20
Right Weigh 221-SK Installation Manual preview
221-SK
Brand: Right Weigh Pages: 16
Fast Master Products SWIVELWHEEL-46 Assembly Instructions Manual preview
SWIVELWHEEL-46
Brand: Fast Master Products Pages: 13
TEINHOF V-295 Fitting And Operation Manual preview
V-295
Brand: TEINHOF Pages: 2

Brands by name

Popular brands

Load more brands