Toyota 1996 LAND CRUISER User Manual Download Page 277

Page: 277 / 1381

BO48P

−

N14081

N14075

−

BODY

WHEEL OPENING MOULDING

1996 LAND CRUISER (RM451U)

REMOVAL

REMOVE FRONT FENDER WHEEL OPENING
MOULDING

(a)

Remove the charcoal canister.

(b)

Remove the air cleaner case assembly.

(c)

Remove the cool air intake duct.

(d)

Remove the front wheel.

(e)

Remove the front mudguard.

(f)

Remove the front bumper extension.

(g)

Remove the 4 nuts from engine room inside service hole.

(h)

Remove the 2 screws.

(i)

Remove the front wheel opening extension.

REAR DOOR SIDE:
REMOVE REAR WHEEL OPENING MOULDING

Remove the 2 bolts and moulding.

REMOVE REAR WHEEL OPENING MOULDING

(a)

Remove the mud guard, bumper extention and back door
scuff plate.

Brought to you by BirfMark

Brought to you by BirfMark
Version 1.00 - 12/21/2010

Summary of Contents for 1996 LAND CRUISER






































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for 1996 LAND CRUISER

Reviews:

Related manuals for 1996 LAND CRUISER

Brands by name

Popular brands

Toyota 1996 LAND CRUISER, User Manual

Search results

Summary of Contents for 1996 LAND CRUISER

Reviews:

Related manuals for 1996 LAND CRUISER

Brands by name

Popular brands