manualshive.com logo in svg

Toyota 1996 LAND CRUISER, User Manual, Page: 641 / 1381

Share
Download
Toyota 1996 LAND CRUISER User Manual Download Page 641

−

DIAGNOSTICS

ANTI

−

LOCK BRAKE SYSTEM

DI

−

209

1996 LAND CRUISER   (RM451U)

2

Check for open and short in harness and connector between ABS ECU and ac-

tuator (See page 

IN

−

28

).

NG

Repair or replace harness or connector.

OK

If same code is still output after DTC is deleted, check contact condition of each connection. If

connector are normal, ECU may be defective.

Brought to you by BirfMark

Brought to you by BirfMark 
 Version 1.00 - 12/21/2010

Summary of Contents for 1996 LAND CRUISER






































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments