Toyota 1996 LAND CRUISER User Manual Download Page 1101

Page: 1101 / 1381

SA2465

SA2406

SST

SA2203

SST

Front

Rear

FA2042

SST

R13140

SST

−

SUSPENSION AND AXLE

FRONT DIFFERENTIAL CARRIER

−

1996 LAND CRUISER (RM451U)

CHECK RING GEAR RUNOUT

(a)

Install the differential case onto the carrier and tighten the
adjusting nut just to where there is no play in the bearings.

(b)

Using a dial indicator, check the ring gear runout.

Maximum runout: 0.10 mm (0.0039 in.)

(c)

Remove the differential case.

INSTALL OIL STORAGE RING

Using SST and a hammer, install a new oil storage ring.

SST

09316

−

60011 (09316

−

00011, 09316

−

00021)

INSTALL DRIVE PINION FRONT AND REAR BEARING
OUTER RACES

Front side:
Using SST and a press, install the 2 outer races.
SST

09316

−

60011 (09316

−

00011, 09316

−

00051)

Rear side:
Using SST and a press, install the 2 outer races.
SST

09316

−

60011 (09316

−

00011, 09316

−

00021)

10. INSTALL DRIVE PINION FRONT BEARING

(a)

Install the plate washer on the drive pinion with the cham-
fered end facing the pinion gear.

(b)

Using SST and a press, install the front bearing onto the
drive pinion.
SST

09506

−

30012

11.

TEMPORARILY ADJUST DRIVE PINION PRELOAD

(a)

Install the drive pinion, rear bearing and oil slinger.

HINT:
Assemble the spacer and oil seal after adjusting the gear con-
tact pattern.
(b)

Install the companion flange with SST.
SST

09550

−

30010 (09951

−

03010, 09953

−

03010,

09954

−

03010, 09955

−

03030, 09956

−

03020)

Brought to you by BirfMark

Brought to you by BirfMark
Version 1.00 - 12/21/2010

«
...
1099
1100
1101
1102
1103
...
»

Summary of Contents for 1996 LAND CRUISER






































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for 1996 LAND CRUISER

Reviews:

Related manuals for 1996 LAND CRUISER

Brands by name

Popular brands

Toyota 1996 LAND CRUISER, User Manual

Search results

Summary of Contents for 1996 LAND CRUISER

Reviews:

Related manuals for 1996 LAND CRUISER

Brands by name

Popular brands